View PSD4135F1V-B-12B81_4745640.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PSD4135G2
Flash In-System-Programmable Peripherals for 16-Bit MCUs
PRELIMINARY DATA
FEATURES SUMMARY s 5 V10% Single Supply Voltage:
s
Figure 1. Packages
Up to 4 Mbit of Primary Flash Memory (8 uniform sectors) 256Kbit Secondary Flash Memory (4 uniform sectors) Up to 64 Kbit SRAM Over 3,000 Gates of PLD: DPLD and CPLD 52 Reconfigurable I/O ports Enhanced JTAG Serial Port Programmable power management High Endurance: - 100,000 Erase/Write Cycles of Flash Memory - 1,000 Erase/Write Cycles of PLD
TQFP80 (U)
s
s s s s s s
January 2002
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
1/3
PSD4000 Series
PSD4135G2 Flash In-System-Programmable Peripherals for 16-Bit MCUs
Table of Contents
Introduction ........................................................................................................................................................................................1 In-System Programming (ISP) JTAG .......................................................................................................................................2 In-Application re-Programming (IAP) .......................................................................................................................................2 Key Features......................................................................................................................................................................................3 PSD4000 Family ................................................................................................................................................................................3 Block Diagram....................................................................................................................................................................................4 Architectural Overview .......................................................................................................................................................................5 Memory ....................................................................................................................................................................................5 PLDs.........................................................................................................................................................................................5 I/O Ports ...................................................................................................................................................................................5 Microcontroller Bus Interface....................................................................................................................................................5 ISP via JTAG Port ....................................................................................................................................................................6 In-System Programming (ISP) .................................................................................................................................................6 In-Application re-Programming (IAP) .......................................................................................................................................6 Page Register...........................................................................................................................................................................6 Power Management Unit ..........................................................................................................................................................6 Development System .........................................................................................................................................................................7 Pin Descriptions .................................................................................................................................................................................8 Register Description and Address Offset .........................................................................................................................................11 Register Bit Definition ......................................................................................................................................................................12 Functional Blocks .............................................................................................................................................................................15 Memory Blocks .......................................................................................................................................................................15 Main Flash and Secondary Flash Memory Description ...................................................................................................15 SRAM...............................................................................................................................................................................26 Memory Select Signals ....................................................................................................................................................26 Page Register ..................................................................................................................................................................29 Memory ID Registers .......................................................................................................................................................30 PLDs.......................................................................................................................................................................................31 Decode PLD (DPLD)........................................................................................................................................................33 General Purpose PLD (GPLD).........................................................................................................................................33 Microcontroller Bus Interface..................................................................................................................................................36 Interface to a Multiplexed Bus..........................................................................................................................................36 Interface to a Non-multiplexed Bus ..................................................................................................................................36 Data Byte Enable Reference ...........................................................................................................................................38 Microcontroller Interface Examples..................................................................................................................................39 I/O Ports .................................................................................................................................................................................44 General Port Architecture ................................................................................................................................................44 Port Operating Modes ......................................................................................................................................................44 Port Configuration Registers (PCRs) ...............................................................................................................................48 Port Data Registers..........................................................................................................................................................49 Ports A, B and C - Functionality and Structure ...............................................................................................................50 Port D - Functionality and Structure ................................................................................................................................51 Port E - Functionality and Structure ................................................................................................................................51 Port F - Functionality and Structure ................................................................................................................................52 Port G - Functionality and Structure ................................................................................................................................52
i
PSD4000 Series
PSD4135G2 Flash In-System-Programmable Peripherals for 16-Bit MCUs
Table of Contents
Power Management ...............................................................................................................................................................53 Automatic Power Down (APD) Unit and Power Down Mode ...........................................................................................53 Other Power Savings Options..........................................................................................................................................57 Reset and Power On Requirement ..................................................................................................................................58 Programming In-Circuit using the JTAG-ISP Interface...........................................................................................................59 Standard JTAG Signals ...................................................................................................................................................60 JTAG Extensions .............................................................................................................................................................60 Security and Flash Memories Protection .........................................................................................................................60 Absolute Maximum Ratings .............................................................................................................................................................61 Operating Range..............................................................................................................................................................................61 Recommended Operating Conditions..............................................................................................................................................61 AC/DC Parameters ..........................................................................................................................................................................62 Example of Typical Power Calculation at Vcc = 5..0 V...........................................................................................................63 Example of Typical Power Calculation at Vcc = 5..0 V in Turbo Off Mode.............................................................................64 DC Characteristics (5 V 10% versions).........................................................................................................................................65 Microcontroller Interface - AC/DC Parameters (5 V 10% versions) .............................................................................................67 DC Characteristics (3.0 V to 3.6 V versions) ...................................................................................................................................71 Microcontroller Interface - AC/DC Parameters (3.0 V to 3.6 V versions) .......................................................................................73 Timing Diagrams ..............................................................................................................................................................................77 Pin Capacitance...............................................................................................................................................................................81 AC Testing Input/Output Waveforms ...............................................................................................................................................81 AC Testing Load Circuit ...................................................................................................................................................................81 Programming ...................................................................................................................................................................................81 Pin Assignments ..............................................................................................................................................................................82 Package Information ........................................................................................................................................................................83 Selector Guide .................................................................................................................................................................................85 Part Number Construction ...............................................................................................................................................................86 Ordering Information ........................................................................................................................................................................86 Document Revisions ........................................................................................................................................................................87 Worldwide Sales, Service and Technical Support ...........................................................................................................................88
ii
PSD4000 Series
PSD4135G2
Configurable Memory System on a Chip for 16-Bit Microcontrollers Preliminary Information
1.0 Introduction
The PSD4000 series of Programmable Microcontroller (MCU) Peripherals brings In-System-Programmability (ISP) to Flash memory and programmable logic. The result is a simple and flexible solution for embedded designs. PSD4000 devices combine many of the peripheral functions found in MCU based applications: * 4 Mbit of Flash memory * A secondary Flash memory for boot or data * Over 3,000 gates of Flash programmable logic * 64 Kbit SRAM * Reconfigurable I/O ports * Programmable power management.
1
PSD4000 Series
Preliminary Information The PSD4135G2 device offers two methods to program PSD Flash memory while the PSD is soldered to a circuit board.
1.0 Introduction
(Cont.)
t In-System Programming (ISP) via JTAG
An IEEE 1149.1 compliant JTAG-ISP interface is included on the PSD enabling the entire device (both flash memories, the PLD, and all configuration) to be rapidly programmed while soldered to the circuit board. This requires no MCU participation, which means the PSD can be programmed anytime, even while completely blank. The innovative JTAG interface to flash memories is an industry first, solving key problems faced by designers and manufacturing houses, such as:
* First time programming - How do I get firmware into the flash the very first time?
JTAG is the answer, program the PSD while blank with no MCU involvement.
* Inventory build-up of pre-programmed devices - How do I maintain an accurate
count of pre-programmed flash memory and PLD devices based on customer demand? How many and what version? JTAG is the answer, build your hardware with blank PSDs soldered directly to the board and then custom program just before they are shipped to customer. No more labels on chips and no more wasted inventory.
* Expensive sockets - How do I eliminate the need for expensive and unreliable
sockets? JTAG is the answer. Solder the PSD directly to the circuit board. Program first time and subsequent times with JTAG. No need to handle devices and bend the fragile leads.
t In-Application re-Programming (IAP)
Two independent flash memory arrays are included so the MCU can execute code from one memory while erasing and programming the other. Robust product firmware updates in the field are possible over any communication channel (CAN, Ethernet, UART, J1850, etc) using this unique architecture. Designers are relieved of these problems:
* Simultaneous read and write to flash memory - How can the MCU program the
same memory from which it is executing code? It cannot. The PSD allows the MCU to operate the two flash memories concurrently, reading code from one while erasing and programming the other during IAP.
* Complex memory mapping - How can I map these two memories efficiently?
A Programmable Decode PLD is embedded in the PSD. The concurrent PSD memories can be mapped anywhere in MCU address space, segment by segment with extremely high address resolution. As an option, the secondary flash memory can be swapped out of the system memory map when IAP is complete. A built-in page register breaks the MCU address limit.
* Separate program and data space - How can I write to flash memory while it
resides in "program" space during field firmware updates, my 80C51XA won't allow it The flash PSD provides means to "reclassify" flash memory as "data" space during IAP, then back to "program" space when complete. PSDsoft - ST's software development tool - guides you through the design process stepby-step making it possible to complete an embedded MCU design capable of ISP/IAP in just hours. Select your MCU and PSDsoft will take you through the remainder of the design with point and click entry, covering...PSD selection, pin definitions, programmable logic inputs and outputs, MCU memory map definition, ANSI C code generation for your MCU, and merging your MCU firmware with the PSD design. When complete, two different device programmers are supported directly from PSDsoft - FlashLINK (JTAG) and PSDpro. The PSD4135G2 is available in an 80-pin TQFP package. Please refer to the revision block at the end of this document for updated information.
2
Preliminary Information
PSD4000 Series
2.0 Key Features
t A simple interface to 16-bit microcontrollers that use either multiplexed or
non-multiplexed busses. The bus interface logic uses the control signals generated by the microcontroller automatically when the address is decoded and a read or write is performed. A partial list of the MCU families supported include: * Intel 80196, 80296, 80186, and 80386EX * Motorola 68HC16, 68HC12, 683XX, and MC2001 * Philips 80C51XA * Infineon C16X devices * Hitachi H8
t 4 Mbit Flash memory. This is the main Flash memory. It is divided into eight
equal-sized blocks that can be accessed with user-specified addresses.
t Internal secondary 256 Kbit Flash boot memory. It is divided into four equal-sized
blocks that can be accessed with user-specified addresses. This secondary memory brings the ability to execute code and update the main Flash concurrently.
t 64 Kbit SRAM. The SRAM's contents can be protected from a power failure by
connecting an external battery.
t General Purpose PLD (GPLD) with 24 outputs. The GPLD may be used to implement
external chip selects or combinatorial logic function.
t Decode PLD (DPLD) that decodes address for selection of internal memory blocks. t 52 individually configurable I/O port pins that can be used for the following functions: * MCU I/Os * PLD I/Os * Latched MCU address output * Special function I/Os. * I/O ports may be configured as open-drain outputs. t Standby current as low as 50 A for 5 V devices. t Built-in JTAG compliant serial port allows full-chip In-System Programmability (ISP).
With it, you can program a blank device or reprogram a device in the factory or the field.
t Internal page register that can be used to expand the microcontroller address space
by a factor of 256.
t Internal programmable Power Management Unit (PMU) that supports a low power
mode called Power Down Mode. The PMU can automatically detect a lack of microcontroller activity and put the PSD4000 into Power Down Mode.
t Erase/Write cycles:
* Flash memory - 100,000 minimum * PLD - 1,000 minimum * 15 year data retention
3.0 PSD4000 Series
Table 1. PSD4000 Product Matrix
Part # PSD4000 Series PSD4000 I/O Pins 52 52 Flash Serial ISP PLD Input Output PLD JTAG/ISP Inputs Macrocells Macrocells Outputs Port 66 82 24 16 24 24 Yes Yes Flash Main Memory Kbit 8 Sectors 4096 4096 Boot Memory Kbit (4 Sectors) 256 256
Device PSD4135G2 PSD4235G2*
SRAM Kbit 64 64
Supply Voltage 5V 5V
*See PSD4235G2 Data Sheet.
3
4
ADDRESS/DATA/CONTROL BUS PLD INPUT BUS
Figure 1. PSD4000 Block Diagram
PSD4000 Series
PAGE REGISTER
4 MBIT MAIN FLASH MEMORY
EMBEDDED ALGORITHM
8 SECTORS POWER MANGMT UNIT
CNTL0, CNTL1, CNTL2
PROG. MCU BUS INTRF. 66
SECTOR SELECTS FLASH DECODE PLD (DPLD) SECTOR SELECTS
SRAM SELECT
256 KBIT SECONDARY FLASH MEMORY (BOOT OR DATA) 4 SECTORS
VSTDBY (PE6)
64 KBIT BATTERY BACKUP SRAM
PROG. PORT PORT A
PA0 - PA7
AD0 - AD15 *
ADIO PORT
CSIOP
RUNTIME CONTROL AND I/O REGISTERS PROG. PORT PORT B
PB0 - PB7
66 PROG. PORT PORT F
FLASH ISP PLD (GPLD)
GPLD OUTPUT
GPLD OUTPUT GPLD OUTPUT
PF0 - PF7
PROG. PORT PORT C
PC0 - PC7
PROG. PORT PROG. PORT PORT G
PD0 - PD3
PG0 - PG7
I/O PORT PLD INPUT
PORT D
Preliminary Information
PROG. PORT
PE0 - PE7
GLOBAL CONFIG. & SECURITY
PLD, CONFIGURATION & FLASH MEMORY LOADER
JTAG SERIAL CHANNEL
PORT E
*Additional address lines can be brought into PSD via Port A, B, C, D, or F.
Preliminary Information
PSD4000 Series PSD4000 devices contain several major functional blocks. Figure 1 on page 3 shows the architecture of the PSD4000 device family. The functions of each block are described briefly in the following sections. Many of the blocks perform multiple functions and are user configurable.
4.0 PSD4000 Architectural Overview
4.1 Memory
The PSD4000 contains the following memories: * 4 Mbit Flash * A secondary 256 Kbit Flash memory for boot or data * 64 Kbit SRAM. Each of the memories is briefly discussed in the following paragraphs. A more detailed discussion can be found in section 9. The 4 Mbit Flash is the main memory of the PSD4000. It is divided into eight equally-sized sectors that are individually selectable. The 256 Kbit secondary Flash memory is divided into four equally-sized sectors. Each sector is individually selectable. The 64 Kbit SRAM is intended for use as a scratchpad memory or as an extension to the microcontroller SRAM. If an external battery is connected to the PSD4000's Vstby pin, data will be retained in the event of a power failure. Each block of memory can be located in a different address space as defined by the user. The access times for all memory types includes the address latching and DPLD decoding time.
4.2 PLDs
The device contains two PLD blocks, each optimized for a different function, as shown in Table 2. The functional partitioning of the PLDs reduces power consumption, optimizes cost/performance, and eases design entry. The Decode PLD (DPLD) is used to decode addresses and generate chip selects for the PSD4000 internal memory and registers. The General Purpose PLD (GPLD) can implement user-defined external chip selects and logic functions. The PLDs receive their inputs from the PLD Input Bus and are differentiated by their output destinations, number of Product Terms. The PLDs consume minimal power by using Zero-Power design techniques. The speed and power consumption of the PLD is controlled by the Turbo Bit in the PMMR0 register and other bits in the PMMR2 registers. These registers are set by the microcontroller at runtime. There is a slight penalty to PLD propagation time when invoking the non-Turbo bit.
4.3 I/O Ports
The PSD4000 has 52 I/O pins divided among seven ports (Port A, B, C, D, E, F and G). Each I/O pin can be individually configured for different functions. Ports can be configured as standard MCU I/O ports, PLD I/O, or latched address outputs for microcontrollers using multiplexed address/data busses. The JTAG pins can be enabled on Port E for In-System Programming (ISP). Ports F and G can also be configured as a data port for a non-multiplexed bus.
4.4 Microcontroller Bus Interface
The PSD4000 easily interfaces with most 16-bit microcontrollers that have either multiplexed or non-multiplexed address/data busses. The device is configured to respond to the microcontroller's control signals, which are also used as inputs to the PLDs. Section 9.3.5 contains microcontroller interface examples.
Table 2. PLD I/O Table
Name Decode PLD General PLD Abbreviation DPLD GPLD Inputs 66 66 Outputs 14 24 Product Terms 40 136 5
PSD4000 Series
Preliminary Information
PSD4000 Architectural Overview
(cont.)
4.5 ISP via JTAG Port
In-System Programming can be performed through the JTAG pins on Port E. This serial interface allows complete programming of the entire PSD4000 device. A blank device can be completely programmed. The JTAG signals (TMS, TCK, TSTAT, TERR, TDI, TDO) can be multiplexed with other functions on Port E. Table 3 indicates the JTAG signals pin assignments.
4.6 In-System Programming (ISP)
Using the JTAG signals on Port E, the entire PSD4000 (memory, logic, configuration) device can be programmed or erased without the use of the microcontroller.
Table 3. JTAG Signals on Port E
Port E Pins
PE0 PE1 PE2 PE3 PE4 PE5
JTAG Signal
TMS TCK TDI TDO TSTAT TERR
4.7 In-Application re-Programming (IAP)
The main Flash memory can also be programmed in-system by the microcontroller executing the programming algorithms out of the secondary Flash memory, or SRAM. Since this is a sizable separate block, the application can also continue to operate. The secondary Flash boot memory can be programmed the same way by executing out of the main Flash memory. Table 4 indicates which programming methods can program different functional blocks of the PSD4000.
Table 4. Methods of Programming Different Functional Blocks of the PSD4000
Functional Block
Main Flash memory Flash Boot memory PLD Array (DPLD and GPLD) PSD Configuration
JTAG-ISP
Yes Yes Yes Yes
Device Programmer
Yes Yes Yes Yes
IAP
Yes Yes No No
4.8 Page Register
The eight-bit Page Register expands the address range of the microcontroller by up to 256 times.The paged address can be used as part of the address space to access external memory and peripherals or internal memory and I/O. The Page Register can also be used to change the address mapping of blocks of Flash memory into different memory spaces for IAP.
4.9 Power Management Unit
The Power Management Unit (PMU) in the PSD4000 gives the user control of the power consumption on selected functional blocks based on system requirements. The PMU includes an Automatic Power Down unit (APD) that will turn off device functions due to microcontroller inactivity. The APD unit has a Power Down Mode that helps reduce power consumption. The PSD4000 also has some bits that are configured at run-time by the MCU to reduce power consumption of the GPLD. The turbo bit in the PMMR0 register can be turned off and the GPLD will latch its outputs and go to standby until the next transition on its inputs. Additionally, bits in the PMMR2 register can be set by the MCU to block signals from entering the GPLD to reduce power consumption. See section 9.5.
6
Preliminary Information
PSD4000 Series The PSD4000 series is supported by PSDsoft a Windows-based (95, 98, NT) software development tool. A PSD design is quickly and easily produced in a point and click environment. The designer does not need to enter Hardware Definition Language (HDL) equations (unless desired) to define PSD pin functions and memory map information. The general design flow is shown in Figure 2 below. PSDsoft is available from our web site (www.psdst.com) or other distribution channels. PSDsoft directly supports two low cost device programmers from ST, PSDpro and FlashLINK (JTAG). Both of these programmers may be purchased through your local rep/distributor, or directly from our web site using a credit card. The PSD4000 is also supported by third party device programmers, see web site for current list.
5.0 Development System
Figure 2. PSDsoft Development Tool
Choose MCU and PSD
Automatically Configures MCU bus interface and other PSD attributes.
Define PSD Pin and Node functions
Point and click definition of PSD pin functions, internal nodes, and MCU system memory map.
C Code Generation
Generate C Code Specific to PSD Functions
Merge MCU Firmware with PSD Configuration
A composite object file is created containing MCU firmware and PSD configuration.
MCU Firmware Hex or S-Record format
User's choice of Microcontroller Compiler/Linker
*.OBJ FILE
PSD Programmer
PSDPro or FlashLink (JTAG)
*.OBJ file available for 3rd party programmers (Conventional or JTAG-ISP)
7
PSD4000 Series
Preliminary Information The following table describes the pin names and pin functions of the PSD4000. Pins that have multiple names and/or functions are defined using PSDsoft. Pin* (TQFP Pkg.)
3-7 10-12
6.0 Table 5. PSD4000 Pin Descriptions
Pin Name
ADIO0-7
Type
I/O
Description
This is the lower Address/Data port. Connect your MCU address or address/data bus according to the following rules: 1. If your MCU has a multiplexed address/data bus where the data is multiplexed with the lower address bits, connect AD[0:7] to this port. 2. If your MCU does not have a multiplexed address/data bus, connect A[0:7] to this port. 3. If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port. ALE or AS latches the address. The PSD drives data out only if the read signal is active and one of the PSD functional blocks was selected. The addresses on this port are passed to the PLDs. This is the upper Address/Data port. Connect your MCU address or address/data bus according to the following rules: 1. If your MCU has a multiplexed address/data bus where the data is multiplexed with the upper address bits, connect AD[8:15] to this port. 2. If your MCU does not have a multiplexed address/data bus, connect A[8:15] to this port. 3. If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this port. ALE or AS latches the address. The PSD drives data out only if the read signal is active and one of the PSD functional blocks was selected. The addresses on this port are passed to the PLDs. The following control signals can be connected to this port, based on your MCU: 1. WR -- active-low write input. 2. R_W -- active-high read/active low write input. 3. WRL -- Write to low byte, active low This pin is connected to the PLDs. Therefore, these signals can be used in decode and other logic equations. The following control signals can be connected to this port, based on your MCU: 1. RD -- active-low read input. 2. E -- E clock input. 3. DS -- active-low data strobe input. 4. LDS -- Strobe for low data byte, active low. This pin is connected to the PLDs. Therefore, these signals can be used in decode and other logic equations. Read or other Control input pin with multiple configurations. Depending on the MCU interface selected, this pin can be: 1. PSEN -- Program Select enable, active low in code fetch bus cycle (80C51XA mode) 2. BHE -- High byte enable. 3. UDS -- Strobe for high data byte, 16-bit data bus mode, active low. 4. SIZ0 -- Byte enable input. 5. LSTRB -- Low strobe input. This pin is also connected to PLD as input.
ADIO8-15
13-20
I/O
CNTL0
59
I
CNTL1
60
I
CNTL2
40
I
8
Preliminary Information
PSD4000 Series Pin* (TQFP Pin Name Pkg.)
Reset 39
Table 5. PSD4000 Pin Descriptions
(cont.)
Type
I
Description
Active low input. Resets I/O Ports, PLD MicroCells, some of the configuration registers and JTAG registers. Must be active at power up. Reset also aborts the Flash programming/erase cycle that is in progress. Port A, PA0-7. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port 2. GPLD output. 3. Input to the PLD (can also be PLD input for address A16 and above). Port B, PB0-7. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. GPLD output. 3. Input to the PLD (can also be PLD input for address A16 and above). Port C, PC0-7. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. External chip select (ECS0-7) output. 3. Input to the PLD (can also be PLD input for address A16 and above). Port D pin PD0 can be configured as: 1. ALE or AS input -- latches addresses on ADIO0-15 pins 2. AS input -- latches addresses on ADIO0-15 pins on the rising edge. 3. Input to the PLD (can also be PLD input for address A16 and above). Port D pin PD1 can be configured as: 1. MCU I/O 2. Input to the PLD (can also be PLD input for address A16 and above). 3. CLKIN clock input -- clock input to the GPLD MicroCells, the APD power down counter and GPLD AND Array. Port D pin PD2 can be configured as: 1. MCU I/O 2. Input to the PLD (can also be PLD input for address A16 and above). 3. CSI input -- chip select input. When low, the CSI enables the internal PSD memories and I/O. When high, the internal memories are disabled to conserve power. CSI trailing edge can get the part out of power-down mode. Port D pin PD3 can be configured as: 1. MCU I/O 2. Input to the PLD (can also be PLD input for address A16 and above). 3. WRH -- for 16-bit data bus, write to high byte, active low. Port E, PE0. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. TMS input for JTAG/ISP interface.
PA0-PA7 51-58
I/O CMOS or Open Drain
PB0-PB7 61-68
I/O CMOS or Open Drain
PC0-PC7 41-48
I/O CMOS or Slew Rate
PD0
79
I/O CMOS or Open Drain
PD1
80
I/O CMOS or Open Drain
PD2
1
I/O CMOS or Open Drain
PD3
2
I/O CMOS or Open Drain I/O CMOS or Open Drain
PE0
71
9
PSD4000 Series
Preliminary Information Pin* (TQFP Pin Name Pkg.)
PE1 72
Table 5. PSD4000 Pin Descriptions
(cont.)
Type
I/O CMOS or Open Drain I/O CMOS or Open Drain I/O CMOS or Open Drain I/O CMOS or Open Drain
Description
Port E, PE1. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. TCK input for JTAG/ISP interface (Schmidt Trigger). Port E, PE2. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. TDI input for JTAG/ISP interface. Port E, PE3. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. TDO output for JTAG/ISP interface. Port E, PE4. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. TSTAT output for the ISP interface. 4. Rdy/Bsy -- for in-circuit Parallel Programming. Port E, PE5. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. TERR active low output for ISP interface. Port E, PE6. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. Vstby -- SRAM standby voltage input for battery backup SRAM Port E, PE7. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address output. 3. Vbaton -- battery backup indicator output. Goes high when power is drawn from an external battery. Port F, PF0-7. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Input to the PLD. 3. Latched address outputs. 4. As address A1-3 inputs in 80C51XA mode (PF0 is grounded) 5. As data bus port (D0-7) in non-multiplexed bus configuration 6. MCU reset mode. Port G, PG0-7. This port is pin configurable and has multiple functions: 1. MCU I/O -- standard output or input port. 2. Latched address outputs. 3. As data bus port (D8-15) in non-multiplexed bus configuration. 4. MCU reset mode.
PE2
73
PE3
74
PE4
75
PE5
76
I/O CMOS or Open Drain I/O CMOS or Open Drain
PE6
77
PE7
78
I/O CMOS or Open Drain
PF0-PF7
31-38
I/O CMOS or Open Drain
PG0-PG7 21-28
I/O CMOS or Open Drain
GND
8,30, 49,50, 70 9,29, 69
VCC
10
Preliminary Information
PSD4000 Series Table 6 shows the offset addresses to the PSD4000 registers relative to the CSIOP base address. The CSIOP space is the 256 bytes of address that is allocated by the user to the internal PSD4000 registers. Table 6 provides brief descriptions of the registers in CSIOP space. For a more detailed description, refer to section 9.
7.0 PSD4000 Register Description and Address Offset
Table 6. Register Address Offset
Register Name
Data In Control Data Out Direction 04 06 05 07 14 16 15 17
Port A
00
Port B
01
Port C
10
Port D
11
Port E
30 32 34 36
Port F
40 42 44 46
Port G
41 43 45 47
Other*
Description
Reads Port pin as input, MCU I/O input mode Selects mode between MCU I/O or Address Out Stores data for output to Port pins, MCU I/O output mode Configures Port pin as input or output Configures Port pins as either CMOS or Open Drain on some pins, while selecting high slew rate on other pins. Read only - Flash Sector Protection Read only - PSD Security and Flash Boot Sector Protection Power Management Register 0 Power Management Register 2 Page Register Places PSD memory areas in Program and/or Data space on an individual basis. Read only - Flash and SRAM size Read only - Boot type and size
Drive Select
08
09
18
19
38
48
49
Flash Protection Flash Boot Protection PMMR0 PMMR2 Page VM
C0
C2 B0 B4 E0 E2
Memory_ID0 Memory_ID1
F0 F1
11
PSD4000 Series
Preliminary Information All the registers in the PSD4000 are included here for reference. Detail description of the registers are found in the Functional Block section of the Data Sheet. Data In Registers - Port A, B, C, D, E, F and G Bit 7
Port Pin 7
8.0 Register Bit Definition
Bit 6
Port Pin 6
Bit 5
Port Pin 5
Bit 4
Port Pin 4
Bit 3
Port Pin 3
Bit 2
Port Pin 2
Bit 1
Bit 0
Port Pin 1 Port Pin 0
Bit definitions: Read only registers, read Port pin status when Port is in MCU I/O input Mode. Data Out Registers - Port A, B, C, D, E, F and G Bit 7
Port Pin 7
Bit 6
Port Pin 6
Bit 5
Port Pin 5
Bit 4
Port Pin 4
Bit 3
Port Pin 3
Bit 2
Port Pin 2
Bit 1
Bit 0
Port Pin 1 Port Pin 0
Bit definitions: Latched data for output to Port pin when pin is configured in MCU I/O output mode. Direction Registers - Port A, B, C, D, E, F and G Bit 7
Port Pin 7
Bit 6
Port Pin 6
Bit 5
Port Pin 5
Bit 4
Port Pin 4
Bit 3
Port Pin 3
Bit 2
Port Pin 2
Bit 1
Bit 0
Port Pin 1 Port Pin 0
Bit definitions: Set Register Bit to 0 = configure corresponding Port pin in Input mode (default). Set Register Bit to 1 = configure corresponding Port pin in Output mode. Control Registers - Ports E, F and G Bit 7
Port Pin 7
Bit 6
Port Pin 6
Bit 5
Port Pin 5
Bit 4
Port Pin 4
Bit 3
Port Pin 3
Bit 2
Port Pin 2
Bit 1
Bit 0
Port Pin 1 Port Pin 0
Bit definitions: Set Register Bit to 0 = configure corresponding Port pin in MCU I/O mode (default). Set Register Bit to 1 = configure corresponding Port pin in Latched Address Out mode. Drive Registers - Ports A, B, D, E, and G Bit 7
Port Pin 7
Bit 6
Port Pin 6
Bit 5
Port Pin 5
Bit 4
Port Pin 4
Bit 3
Port Pin 3
Bit 2
Port Pin 2
Bit 1
Bit 0
Port Pin 1 Port Pin 0
Bit definitions: Set Register Bit to 0 = configure corresponding Port pin in CMOS output driver (default). Set Register Bit to 1 = configure corresponding Port pin in Open Drain output driver. Drive Registers - Ports C and F Bit 7
Port Pin 7
Bit 6
Port Pin 6
Bit 5
Port Pin 5
Bit 4
Port Pin 4
Bit 3
Port Pin 3
Bit 2
Port Pin 2
Bit 1
Bit 0
Port Pin 1 Port Pin 0
Bit definitions: Set Register Bit to 0 = configure corresponding Port pin as CMOS output driver (default). Set Register Bit to 1 = configure corresponding Port pin in Slew Rate mode. Flash Protection Register Bit 7
Sec7_Prot
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Sec6_Prot Sec5_Prot Sec4_Prot
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
Bit definitions: Read Only Register Sec_Prot 1 = Flash Sector is write protected. Sec_Prot 0 = Flash Sector is not write protected.
12
Preliminary Information
PSD4000 Series Flash Boot Protection Register Bit 7
Security_Bit
8.0 Register Bit Definition
(cont.)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
*
*
*
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
Bit definitions: Sec_Prot 1 = Boot Block Sector is write protected. Sec_Prot 0 = Boot Block Sector is not write protected. Security_Bit Page Register Bit 7
Pgr7
0 = Security Bit in device has not been set. 1 = Security Bit in device has been set.
Bit 6
Pgr6
Bit 5
Pgr5
Bit 4
Pgr4
Bit 3
Pgr3
Bit 2
Pgr2
Bit 1
Pgr1
Bit 0
Pgr0
Bit definitions: Configure Page input to PLD. Default Pgr[7:0] = 00. PMMR0 Register Bit 7 Bit 6 Bit 5
PLD Mcells clk
Bit 4
PLD array-clk
Bit 3
PLD Turbo
Bit 2
Bit 1
APD enable
Bit 0
*
*
*
*
*Not used bit should be set to zero. Bit definitions: (default is 0) Bit 1 0 = Automatic Power Down (APD) is disabled. 1 = Automatic Power Down (APD) is enabled. Bit 3 0 = PLD Turbo is on. 1 = PLD Turbo is off, saving power. Bit 4 0 = CLKIN input to the PLD AND array is connected. Every CLKIN change will power up the PLD when Turbo bit is off. 1 = CLKIN input to PLD AND array is disconnected, saving power. Bit 5 0 = CLKIN input to the PLD MicroCells is connected. 1 = CLKIN input to the PLD MicroCells is disconnected, saving power. PMMR2 Register Bit 7 Bit 6
PLD array WRh
Bit 5
PLD array Ale
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
*
PLD PLD PLD array Cntl2 array Cntl1 array Cntl0
*
*
*Not used bit should be set to zero. Bit definitions (defauld is 0): Bit 0 0 = Address A[7:0] are connected into the PLD array. 1 = Address A[7:0] are blocked from the PLD array, saving power. Note: in XA mode, A3-0 come from PF3-0 and A7-4 come from ADIO7-4. Bit 2 0 = Cntl0 input to the PLD AND array is connected. 1 = Cntl0 input to the PLD AND array is disconnected, saving power. Bit 3 0 = Cntl1 input to the PLD AND array is connected. 1 = Cntl1 input to the PLD AND array is disconnected, saving power. Bit 4 0 = Cntl2 input to the PLD AND array is connected. 1 = Cntl2 input to the PLD AND array is disconnected, saving power. Bit 5 0 = Ale input to the PLD AND array is connected. 1 = Ale input to the PLD AND array is disconnected, saving power. Bit 6 0 = WRh/DBE input to the PLD AND array is connected. 1 = WRh/DBE input to the PLD AND array is disconnected, saving power.
13
PSD4000 Series
Preliminary Information VM Register Bit 7 Bit 6 Bit 5 Bit 4
FL_data
8.0 Register Bit Definition
(cont.)
Bit 3
Boot_data
Bit 2
FL_code
Bit 1
Bit 0
*
*
*
Boot_code SR_code
Note: Upon reset, Bit1-Bit4 are loaded to configurations selected by the user in PSDsoft. Bit 0 is always cleared by reset. Bit 0 to Bit 4 are active only when the device is configured in Philips 80C51XA mode. Not used bit should be set to zero.
Bit definitions: Bit 0 0 = PSEN can't access SRAM in 80C51XA modes. 1 = PSEN can access SRAM in 80C51XA modes. Bit 1 0 = PSEN can't access Boot in 80C51XA modes. 1 = PSEN can access Boot in 80C51XA modes. Bit 2 0 = PSEN can't access main Flash in 80C51XA modes. 1 = PSEN can access main Flash in 80C51XA modes. Bit 3 0 = RD can't access Boot in 80C51XA modes. 1 = RD can access Boot in 80C51XA modes. Bit 4 0 = RD can't access main Flash in 80C51XA modes. 1 = RD can access main Flash in 80C51XA modes. Memory_ID0 Register Bit 7
S_size 3
Bit 6
S_size 2
Bit 5
S_size 1
Bit 4
S_size 0
Bit 3
F_size 3
Bit 2
F_size 2
Bit 1
F_size 1
Bit 0
F_size 0
Bit definitions: F_size[3:0] = 4h, main Flash size is 2M bit. F_size[3:0] = 5h, main Flash size is 8M bit. S_size[3:0] = 0h, SRAM size is 0K bit. S_size[3:0] = 1h, SRAM size is 16K bit. S_size[3:0] = 3h, SRAM size is 64K bit. Memory_ID1 Register Bit 7 Bit 6 Bit 5
B_type 1
Bit 4
B_type 0
Bit 3
B_size 3
Bit 2
B_size 2
Bit 1
B_size 1
Bit 0
B_size 0
*
*
*Not used bit should be set to zero. Bit definitions: B_size[3:0] = 0h, Boot block size is 0K bit. B_size[3:0] = 2h, Boot block size is 256K bit. B_type[1:0] = 0h, Boot block is Flash memory.
14
Preliminary Information
PSD4000 Series As shown in Figure 1, the PSD4000 consists of six major types of functional blocks:
9.0 The PSD4000 Functional Blocks
t t t t t t
Memory Blocks PLD Blocks Bus Interface I/O Ports Power Management Unit JTAG-ISP Interface
The functions of each block are described in the following sections. Many of the blocks perform multiple functions, and are user configurable.
9.1 Memory Blocks
The PSD4000 has the following memory blocks: * The main Flash memory * Secondary Flash memory * SRAM. The memory select signals for these blocks originate from the Decode PLD (DPLD) and are user-defined in PSDsoft. Table 7 summarizes which versions of the PSD4000 contain which memory blocks.
Table 7. Memory Blocks
Main Flash Device
PSD4135G2
Secondary Flash Block Size
32KB
Flash Size
512KB
Sector Size
64KB
Sector Size
8KB
SRAM
8KB
9.1.1 Main Flash and Secondary Flash Memory Description The main Flash memory block is divided evenly into eight sectors. The secondary Flash memory is divided into four sectors of eight Kbytes each. Each sector of either memory can be separately protected from program and erase operations. Flash memory may be erased on a sector-by-sector basis and programmed word-by-word. Flash sector erasure may be suspended while data is read from other sectors of memory and then resumed after reading. During a program or erase of Flash, the status can be output on the Rdy/Bsy pin of Port PE4. This pin is set up using PSDsoft. 9.1.1.1 Memory Block Selects The decode PLD in the PSD4000 generates the chip selects for all the internal memory blocks (refer to the PLD section). Each of the eight Flash memory sectors have a Flash Select signal (FS0-FS7) which can contain up to three product terms. Each of the four Secondary Flash memory sectors have a Select signal (CSBOOT0-3) which can contain up to three product terms. Having three product terms for each sector select signal allows a given sector to be mapped in different areas of system memory. When using a microcontroller (80C51XA) with separate Program and Data space, these flexible select signals allow dynamic re-mapping of sectors from one space to the other before and after IAP. 9.1.1.2 The Ready/Busy Pin (PE4) Pin PE4 can be used to output the Ready/Busy status of the PSD4000. The output on the pin will be a `0' (Busy) when Flash memory blocks are being written to, or when the Flash memory block is being erased. The output will be a `1' (Ready) when no write or erase operation is in progress.
15
PSD4000 Series
Preliminary Information 9.1.1.3 Memory Operation The main Flash and secondary Flash memories are addressed through the microcontroller interface on the PSD4000 device. The microcontroller can access these memories in one of two ways:
The PSD4000 Functional Blocks
(cont.)
t The microcontroller can execute a typical bus write or read operation just as it would
if accessing a RAM or ROM device using standard bus cycles.
t The microcontroller can execute a specific instruction that consists of several write
and read operations. This involves writing specific data patterns to special addresses within the Flash to invoke an embedded algorithm. These instructions are summarized in Table 8. Typically, Flash memory can be read by the microcontroller using read operations, just as it would read a ROM device. However, Flash memory can only be erased and programmed with specific instructions. For example, the microcontroller cannot write a single word directly to Flash memory as one would write a word to RAM. To program a word into Flash memory, the microcontroller must execute a program instruction sequence, then test the status of the programming event. This status test is achieved by a read operation or polling the Rdy/Busy pin (PE4). The Flash memory can also be read by using special instructions to retrieve particular Flash device information (sector protect status and ID). 9.1.1.3.1 Instructions An instruction is defined as a sequence of specific operations. Each received byte is sequentially decoded by the PSD and not executed as a standard write operation. The instruction is executed when the correct number of bytes are properly received and the time between two consecutive bytes is shorter than the time-out value. Some instructions are structured to include read operations after the initial write operations. The sequencing of any instruction must be followed exactly. Any invalid combination of instruction bytes or time-out between two consecutive bytes while addressing Flash memory will reset the device logic into a read array mode (Flash memory reads like a ROM device). The PSD4000 main Flash and secondary Flash support these instructions (see Table 8):
t t t t t t t
Erase memory by chip or sector Suspend or resume sector erase Program a word Reset to read array mode Read Main Flash Identifier value Read sector protection status Bypass Instruction
These instructions are detailed in Table 8. For efficient decoding of the instructions, the first two bytes of an instruction are the coded cycles and are followed by a command byte or confirmation byte. The coded cycles consist of writing the data byte AAh to address XAAAh during the first cycle and data byte 55h to address X554h during the second cycle (unless the Bypass Instruction feature is used. See 9.1.1.7). Address lines A15-A12 are don't care during the instruction write cycles. However, the appropriate sector select signal (FSi or CSBOOTi) must be selected. The main Flash and the secondary Flash Block have the same set of instructions (except Read main Flash ID). The chip selects of the Flash memory will determine which Flash will receive and execute the instruction. The main Flash is selected if any one of the FS0-7 is active, and the secondary Flash Block is selected if any one of the CSBOOT0-3 is active.
16
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Table 8. Instructions
Instruction
(Note 14) Read (Note 5) Read Main Flash ID (Note 6) Read Sector Protection (Notes 6,8,13) Program a Flash Word Erase One Flash Sector
FS0-7 or CSBOOT0-3 Cycle 1 Cycle 2 Cycle 3
1 1 "Read" RA RD AAh 55h 90h @XAAAh @X554h @XAAAh
Cycle 4
Cycle5
Cycle 6
Cycle 7
"Read" ID @XX02h
1
AAh 55h 90h "Read" @XAAAh @X554h @XAAAh 00h or 01h @XX04h AAh 55h A0h @XAAAh @X554h @XAAAh AAh 55h 80h @XAAAh @X554h @XAAAh AAh 55h 80h @XAAAh @X554h @XAAAh B0h @xxxh 30h @xxxh F0 @ any address AAh 55h 20h @XAAAh @X554h @XAAAh A0h PD@PA @XXXXh 90h 00h @XXXXh @XXXXh PD@PA AAh @XAAAh AAh @XAAAh 55h @X554h 55h @X554h 30h @SA 10h @XAAAh 30h @next SA (Note 7)
1 1
Erase Flash Block (Bulk Erase) Suspend Sector Erase (Note 11) Resume Sector Erase (Note 12) Reset (Note 6) Unlock Bypass Unlock Bypass Program (Note 9) Unlock Bypass Reset (Note 10)
1 1 1 1 1 1 1
Don't Care. "xxxh" address in the above table must be an even address. Address of the memory location to be read. Data read from location RA during read operation. Address of the memory location to be programmed. Addresses are latched on the falling edge of the WR# (CNTL0) pulse. PA is an even address for PSD in word programming mode. PD = Data (word) to be programmed at location PA. Data is latched on the rising edge of WR# (CNTL0) pulse. SA = Address of the sector to be erased or verified. The chip select (FS0-7 or CSBOOT0-3) of the sector to be erased must be active (high). NOTES: 1. All bus cycles are write bus cycle except the ones with the "read" label. 2. All values are in hexadecimal. 3. FS0-7 and CSBOOT0-3 are active high and are defined in PSDsoft. 4. Only Address bits A11-A0 are used in Instruction decoding. 5. No unlock or command cycles required when device is in read mode. 6. The Reset command is required to return to the read mode after reading the Flash ID, Sector Protect status or if DQ5 (DQ13) goes high. 7. Additional sectors to be erased must be entered within 80s. 8. The data is 00h for an unprotected sector and 01h for a protected sector. In the fourth cycle, the sector chip select is active and (A1 = 1, A0 = 0). 9. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the Unlock Bypass mode. 11. The system may read and program functions in non-erasing sectors, read the Flash ID or read the Sector Protect status, when in the Erase Suspend mode. The erase Suspend command is valid only during a sector erase operation. 12. The Erase Resume command is valid only during the Erase Suspend mode. 13. The MCU cannot invoke these instructions while executing code from the same Flash memory for which the instruction is intended. The MCU must fetch, for example, codes from the Secondary Flash memory when reading the Sector Protection Status of the main Flash. 14. All write bus cycles in an instruction are byte write to even address (XA4Ah or X554h). Flash Programming bys cycle is writing a word to even address.
X RA RD PA
= = = =
17
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.1.1.4 Power-Up Condition
The PSD4000 internal logic is reset upon power-up to the read array mode. The FSi and CSBOOTi select signals, along with the write strobe signal, must be in the false state during power-up for maximum security of the data contents and to remove the possibility of data being written on the first edge of a write strobe signal. Any write cycle initiation is locked when VCC is below VLKO.
9.1.1.5 Read
Under typical conditions, the microcontroller may read the Flash, or secondary Flash memories using read operations just as it would a ROM or RAM device. Alternately, the microcontoller may use read operations to obtain status information about a program or erase operation in progress. Lastly, the microcontroller may use instructions to read special data from these memories. The following sections describe these read functions. 9.1.1.5.1 Read the Contents of Memory Main Flash and secodary Flash memories are placed in the read array mode after power-up, chip reset, or a Reset Flash instruction (see Table 8). The microcontroller can read the memory contents of main Flash or secondary Flash by using read operations any time the read operation is not part of an instruction sequence. 9.1.1.5.2 Read the Main Flash Memory Identifier The main Flash memory identifier is read with an instruction composed of 4 operations: 3 specific write operations and a read operation (see Table 8). The PSD4000 main Flash memory ID is E8h. The Secondary Flash does not support this instruction. 9.1.1.5.3 Read the Flash Memory Sector Protection Status The Flash memory sector protection status is read with an instruction composed of 4 operations: 3 specific write operations and a read operation (see Table 8). The read operation will produce 01h if the Flash sector is protected, or 00h if the sector is not protected. The sector protection status for all NVM blocks (main Flash or secondary Flash) can also be read by the microcontroller accessing the Flash Protection and Flash Boot Protection registers in PSD I/O space. See section 9.1.1.9.1 for register definitions. 9.1.1.5.4 Read the Erase/Program Status Bits The PSD4000 provides several status bits to be used by the microcontroller to confirm the completion of an erase or programming instruction of Flash memory. These status bits minimize the time that the microcontroller spends performing these tasks and are defined in Table 9. The status byte resides in even location and can be read as many times as needed. Please note DQ15-8 is even byte for Motorola MCUs with 16 bit data bus.
Table 9. Status Bits
FSi/ CSBOOTi
Flash VIH
DQ7
Data Polling
DQ6
Toggle Flag
DQ5
Error Flag
DQ4
X
DQ3
Erase Timeout
DQ2
X
DQ1
X
DQ0
X
Table 9A. Status Bits for Motorola
FSi/ CSBOOTi
Flash VIH
DQ15
Data Polling
DQ14
Toggle Flag
DQ13
Error Flag
DQ12
X
DQ11
Erase Timeout
DQ10
X
DQ9
X
DQ8
X
NOTES: 1. X = Not guaranteed value, can be read either 1 or 0. 2. DQ15-DQ0 represent the Data Bus bits, D15-D0. 3. FSi/CSBOOTi are active high.
For Flash memory, the microcontroller can perform a read operation to obtain these status bits while an erase or program instruction is being executed by the embedded algorithm. See section 9.1.1.6 for details. 18
Preliminary Information
PSD4000 Series 9.1.1.5.5 Data Polling Flag DQ7 (DQ15 for Motorola) When Erasing or Programming the Flash memory bit DQ7 (DQ15) outputs the complement of the bit being entered for Programming/Writing on DQ7 (DQ15). Once the Program instruction or the Write operation is completed, the true logic value is read on DQ7 (DQ15) (in a Read operation). Flash memory specific features:
The PSD4000 Functional Blocks
(cont.)
t Data Polling is effective after the fourth Write pulse (for programming) or after the t t t
sixth Write pulse (for Erase). It must be performed at the address being programmed or at an address within the Flash sector being erased. During an Erase instruction, DQ7 (DQ15) outputs a `0'. After completion of the instruction, DQ7 (DQ15) will output the last bit programmed (it is a `1' after erasing). If the location to be programmed is in a protected Flash sector, the instruction is ignored. If all the Flash sectors to be erased are protected, DQ7 (DQ15) will be set to `0' for about 100 s, and then return to the previous addressed location. No erasure will be performed.
9.1.1.5.6 Toggle Flag DQ6 (DQ14 for Motorola) The PSD4000 offers another way for determining when the Flash memory Program instruction is completed. During the internal Write operation and when either the FSi or CSBOOTi is true, the DQ6 (DQ14) will toggle from `0' to `1' and `1' to `0' on subsequent attempts to read any word of the memory. When the internal cycle is complete, the toggling will stop and the data read on the Data Bus is the addressed memory location. The device is now accessible for a new Read or Write operation. The operation is finished when two successive reads yield the same output data. Flash memory specific features:
t The Toggle bit is effective after the fourth Write pulse (for programming) or after the t t
sixth Write pulse (for Erase). If the location to be programmed belongs to a protected Flash sector, the instruction is ignored. If all the Flash sectors selected for erasure are protected, DQ6 (DQ14) will toggle to `0' for about 100 s and then return to the previous addressed location.
9.1.1.5.7 Error Flag DQ5 (DQ14 for Motorola) During a correct Program or Erase, the Error bit will set to `0'. This bit is set to `1' when there is a failure during Flash programming, Sector erase, or Bulk Erase. In the case of Flash programming, the Error Bit indicates the attempt to program a Flash bit(s) from the programmed state (0) to the erased state (1), which is not a valid operation. The Error bit may also indicate a timeout condition while attempting to program a word. In case of an error in Flash sector erase or word program, the Flash sector in which the error occurred or to which the programmed location belongs must no longer be used. Other Flash sectors may still be used. The Error bit resets after the Reset instruction. A reset instruction is required after detecting the error bit. 9.1.1.5.8 Erase Time-out Flag DQ3 (DQ11 for Motorola) The Erase Timer bit reflects the time-out period allowed between two consecutive Sector Erase instructions. The Erase timer bit is set to `0' after a Sector Erase instruction for a time period of 100 s + 20% unless an additional Sector Erase instruction is decoded. After this time period or when the additional Sector Erase instruction is decoded, DQ3 (DQ11) is set to `1'. A reset instruction is required after detecting the erase timer bit.
19
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.1.1.6 Programming Flash Memory
Flash memory must be erased prior to being programmed. The MCU may erase Flash memory all at once or by-sector. Flash memory sector erases to all logic ones, and its bits are programmed to logic zeros. Although erasing Flash memory occurs on a sector or chip basis, programming Flash memory occurs on a word basis. The PSD4000 main Flash and secondary Flash memories require the MCU to send an instruction to program a word or perform an erase function (see Table 8). Once the MCU issues a Flash memory program or erase instruction, it must check for the status of completion. The embedded algorithms that are invoked inside the PSD4000 support several means to provide status to the MCU. Status may be checked using any of three methods: Data Polling, Data Toggle, or the Ready/Busy output pin. 9.1.1.6.1 Data Polling Polling on DQ7 (DQ15) is a method of checking whether a Program or Erase instruction is in progress or has completed. Figure 3 shows the Data Polling algorithm. When the MCU issues a programming instruction, the embedded algorithm within the PSD4000 begins. The MCU then reads the location of the word to be programmed in Flash to check status. Data bit DQ7 (DQ15) of this location becomes the compliment of data bit 7of the original data word to be programmed. The MCU continues to poll this location, comparing DQ7 (DQ15) and monitoring the Error bit on DQ5 (DQ13). When the DQ7 (DQ15) matches data bit 7 of the original data, and the Error bit at DQ5 (DQ13) remains `0', then the embedded algorithm is complete. If the Error bit at DQ5 is `1', the MCU should test DQ7 (DQ15) again since DQ7 (DQ15) may have changed simultaneously with DQ5 (DQ13) (see Figure 3). The Error bit at DQ5 (DQ13) will be set if either an internal timeout occurred while the embedded algorithm attempted to program the location or if the MCU attempted to program a `1' to a bit that was not erased (not erased is logic `0'). It is suggested (as with all Flash memories) to read the location again after the embedded programming algorithm has completed to compare the word that was written to Flash with the word that was intended to be written. When using the Data Polling method after an erase instruction, Figure 3 still applies. However, DQ7 (DQ15) will be `0' until the erase operation is complete. A `1' on DQ5 (DQ13) will indicate a timeout failure of the erase operation, a `0' indicates no error. The MCU can read any location within the sector being erased to get DQ7 (DQ15) and DQ5 (DQ13) . PSDsoft generates ANSI C code functions which implement these Data Polling algorithms.
20
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Figure 3. Data Polling Flow Chart
START
READ DQ5 & DQ7 (DQ13 & DQ15) at VALID EVEN ADDRESS
DQ7 (DQ15) = DATA7 (DATA15)
YES
NO NO DQ5 (DQ13) =1 YES READ DQ7 (DQ15)
DQ7 (DQ15) = DATA7 (DATA15) NO FAIL Program/Erase Operation Failed Issue Reset Instruction
YES
PASS Program/Erase Operation is Completed
9.1.1.6.2 Data Toggle Checking the Data Toggle bit on DQ6 (DQ14) is a method of determining whether a Program or Erase instruction is in progress or has completed. Figure 4 shows the Data Toggle algorithm. When the MCU issues a programming instruction, the embedded algorithm within the PSD4000 begins. The MCU then reads the location to be programmed in Flash to check status. Data bit DQ6 (DQ14) of this location will toggle each time the MCU reads this location until the embedded algorithm is complete. The MCU continues to read this location, checking DQ6 (DQ14) and monitoring the Error bit on DQ5 (DQ13) . When DQ6 (DQ14) stops toggling (two consecutive reads yield the same value), and the Error bit on DQ5 (DQ13) remains `0', then the embedded algorithm is complete. If the Error bit on DQ5 (DQ13) is `1', the MCU should test DQ6 (DQ14) again, since DQ6 (DQ14) may have changed simultaneously with DQ5 (DQ13) (see Figure 4). The Error bit at DQ5 (DQ13) will be set if either an internal timeout occurred while the embedded algorithm attempted to program, or if the MCU attempted to program a `1' to a bit that was not erased (not erased is logic `0').
21
PSD4000 Series
Preliminary Information 9.1.1.6.2 Data Toggle (cont.) It is suggested (as with all Flash memories) to read the location again after the embedded programming algorithm has completed to compare the word that was written to Flash with the word that was intended to be written. When using the Data Toggle method after an erase instructin, Figure 4 still applies. DQ6 (DQ14) will toggle until the erase operation is complete. A `1' on DQ5 (DQ13) will indicate a timeout failure of the erase operation, a `0' indicates no error. The MCU can read any even location within the sector being erased to get DQ6 (DQ14) and DQ5 (DQ13) . PSDsoft generates ANSI C code functions which implement these Data Toggling algorithms.
The PSD4000 Functional Blocks
(cont.)
Figure 4. Data Toggle Flow Chart
START
READ DQ5 & DQ6 (DQ13 & DQ14) at VALID EVEN ADDRESS
DQ6 (DQ14) = TOGGLE
NO
YES NO DQ5 (DQ13) =1 YES READ DQ6 (DQ14)
DQ6 (DQ14) = TOGGLE
NO
YES FAIL Program/Erase Operation Failed Issue Reset Instruction PASS Program/Erase Operation is Completed
22
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
9.1.1.7 Unlock Bypass Instruction
The unlock bypass feature allows the system to program words to the flash memories faster than using the standard program instruction. The unlock bypass instruction is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h (see Table 8). The flash memory then enters the unlock bypass mode. A two-cycle Unlock Bypass Program instruction is all that is required to program in this mode. The first cycle in this instruction contains the unlock bypass programm command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program instruction, resulting in faster total programming time. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset instructions are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset instruction. The first cycle must contain the data 90h; the second cycle the data 00h. Addresses are don't care for both cycles. The flash memory then returns to reading array data mode.
9.1.1.8 Erasing Flash Memory
9.1.1.8.1. Flash Bulk Erase Instruction The Flash Bulk Erase instruction uses six write operations followed by a Read operation of the status register, as described in Table 8. If any byte of the Bulk Erase instruction is wrong, the Bulk Erase instruction aborts and the device is reset to the Read Flash memory status. During a Bulk Erase, the memory status may be checked by reading status bits DQ5, DQ6, and DQ7 (DQ13, DQ14, DQ15), as detailed in section 9.1.1.6. The Error bit (returns a `1' if there has been an Erase Failure (maximum number of erase cycles have been executed). It is not necessary to program the array with 00h because the PSD4000 will automatically do this before erasing to 0FFh. During execution of the Bulk Erase instruction, the Flash memory will not accept any instructions. 9.1.1.8.2 Flash Sector Erase Instruction The Sector Erase instruction uses six write operations, as described in Table 8. Additional Flash Sector Erase confirm commands and Flash sector addresses can be written subsequently to erase other Flash sectors in parallel, without further coded cycles, if the additional instruction is transmitted in a shorter time than the timeout period of about 100 s. The input of a new Sector Erase instruction will restart the time-out period. The status of the internal timer can be monitored through the level of DQ3 (DQ11) (Erase time-out bit). If DQ3 (DQ11) is `0', the Sector Erase instruction has been received and the timeout is counting. If DQ3 (DQ11) is `1', the timeout has expired and the PSD4000 is busy erasing the Flash sector(s). Before and during Erase timeout, any instruction other than Erase suspend and Erase Resume will abort the instruction and reset the device to Read Array mode. It is not necessary to program the Flash sector with 00h as the PSD4000 will do this automatically before erasing. During a Sector Erase, the memory status may be checked by reading status bits DQ5, DQ6, and DQ7 (DQ13, DQ14, DQ15), as detailed in section 9.1.1.6. During execution of the erase instruction, the Flash block logic accepts only Reset and Erase Suspend instructions. Erasure of one Flash sector may be suspended, in order to read data from another Flash sector, and then resumed.
23
PSD4000 Series
Preliminary Information 9.1.1.8.3 Flash Erase Suspend Instruction When a Flash Sector Erase operation is in progress, the Erase Suspend instruction will suspend the operation by writing 0B0h to any even address when an appropriate Chip Select (FSi or CSBOOTi) is true. (See Table 8). This allows reading of data from another Flash sector after the Erase operation has been suspended. Erase suspend is accepted only during the Flash Sector Erase instruction execution and defaults to read array mode. An Erase Suspend instruction executed during an Erase timeout will, in addition to suspending the erase, terminate the time out. The Toggle Bit DQ6 stops toggling when the PSD4000 internal logic is suspended. The toggle Bit status must be monitored at an address within the Flash sector being erased. The Toggle Bit will stop toggling between 0.1 s and 15 s after the Erase Suspend instruction has been executed. The PSD4000 will then automatically be set to Read Flash Block Memory Array mode. If an Erase Suspend instruction was executed, the following rules apply: * Attempting to read from a Flash sector that was being erased will output invalid data. * Reading from a Flash sector that was not being erased is valid. * The Flash memory cannot be programmed, and will only respond to Erase Resume and Reset instructions (read is an operation and is OK). * If a Reset instruction is received, data in the Flash sector that was being erased will be invalid. 9.1.1.8.4 Flash Erase Resume Instruction If an Erase Suspend instruction was previously executed, the erase operation may be resumed by this instruction. The Erase Resume instruction consists of writing 030h to any even address while an appropriate Chip Select (FSi or CSBOOTi) is true. (See Table 8.)
The PSD4000 Functional Blocks
(cont.)
9.1.1.9 Specific Features
9.1.1.9.1 Main Flash and Secondary Flash Sector Protect Each sector of Main Flash and Secondary Flash memory can be separately protected against Program and Erase functions. Sector Protection provides additional data security because it disables all program or erase operations. This mode can be activated (or deactivated) through the JTAG-ISP Port or a Device Programmer. Sector protection can be selected for each sector using the PSDsoft program. This will automatically protect selected sectors when the device is programmed through the JTAG Port or a Device Programmer. Flash sectors can be unprotected to allow updating of their contents using the JTAG Port or a Device Programmer. The microcontroller can read (but cannot change) the sector protection bits. Any attempt to program or erase a protected Flash sector will be ignored by the device. The Verify operation will result in a read of the protected data. This allows a guarantee of the retention of the Protection status. The sector protection status can either be read by the MCU through the Flash protection and secondary Flash protection registers (CSIOP), or use the Read Sector Protection instruction (Table 8).
24
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Table 10. Sector Protection/Security Bit Definition
Flash Protection Register Bit 7
Sec7_Prot
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Sec6_Prot Sec5_Prot Sec4_Prot
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
Bit Definitions: Sec_Prot Sec_Prot
1 = Main Flash Sector is write protected. 0 = Main Flash Sector is not write protected.
Flash Boot Protection Register Bit 7
Security_ Bit
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
*
*
*
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
*:
Not used.
Bit Definitions: Sec_Prot Sec_Prot Security_Bit
1 = Flash Boot Sector is write protected. 0 = Flash Boot Sector is not write protected. 0 = Security Bit in device has not been set. 1 = Security Bit in device has been set.
9.1.1.9.2 Reset Instruction The Reset instruction consists of one write cycle (see Table 8). It can also be optionally preceded by the standard two write decoding cycles (writing AAh to AAAh and 55h to 554h). The Reset instruction must be executed after: 1. Reading the Flash Protection status or Flash ID using the Flash instruction. 2. When an error condition occurs (DQ5 (DQ13) goes high) during a Flash programming or erase cycle. The Reset instruction will reset the Flash to normal Read Mode immediately. However, if there is an error condition (DQ5 (DQ13) goes high), the Flash memory will return to the Read Mode in 25 Seconds after the Reset instruction is issued. The Reset instruction is ignored when it is issued during a Flash programming or Bulk Erase cycle. The Reset instruction will abort the on going sector erase cycle and return the Flash memory to normal Read Mode in 25 Seconds. 9.1.1.9.3 Reset Pin Input The reset pulse input from the pin will abort any operation in progress and reset the Flash memory to Read Mode. When the reset occurs during a programming or erase cycle, the Flash memory will take up to 25 Seconds to return to Read Mode. It is recommended that the reset pulse (except power on reset, see Reset Section) be at least 25 Seconds such that the Flash memory will always be ready for the MCU to fetch the boot code after reset is over.
25
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.1.2 SRAM
The SRAM is enabled when RS0-- the SRAM chip select output from the DPLD-- is high. RS0 can contain up to three product terms, allowing flexible memory mapping. The SRAM can be backed up using an external battery. The external battery should be connected to the Vstby pin (PE6). If you have an external battery connected to the PSD4000, the contents of the SRAM will be retained in the event of a power loss. The contents of the SRAM will be retained so long as the battery voltage remains at 2V or greater. If the supply voltage falls below the battery voltage, an internal power switchover to the battery occurs. Pin PE7 can be configured as an output that indicates when power is being drawn from the external battery. This Vbaton signal will be high with the supply voltage falls below the battery voltage and the battery on PE6 is supplying power to the internal SRAM. The chip select signal (RS0) for the SRAM, Vstby, and Vbaton are all configured using PSDsoft.
9.1.3 Memory Select Signals
The main Flash (FSi), secondary Flash (CSBOOTi), and SRAM (RS0) memory select signals are all outputs of the DPLD. They are defined using PSDsoft. The following rules apply to the equations for the internal chip select signals: 1. Main Flash memory and secondary Flash memory sector select signals must not be larger than the physical sector size. 2. Any main Flash memory sector must not be mapped in the same memory space as another Main Flash sector. 3. A secondary Flash memory sector must not be mapped in the same memory space as another Flash Boot sector. 4. SRAMand I/O spaces must not overlap. 5. A secondary Flash memory sector may overlap a main Flash memory sector. In case of overlap, priority will be given to the Flash Boot sector. 6. SRAM, I/O, and Peripheral I/O spaces may overlap any other memory sector. Priority will be given to the SRAM, and I/O. Example FS0 is valid when the address is in the range of 8000h to BFFFh, CSBOOT0 is valid from 8000h to 9FFFh, and RS0 is valid from 8000h to 87FFh. Any address in the range of RS0 will always access the SRAM. Any address in the range of CSBOOT0 greater than 87FFh (and less than 9FFFh) will automatically address Boot memory segment 0. Any address greater than 9FFFh will access the Flash memory segment 0. You can see that half of the Flash memory segment 0 and one-fourth of Boot segment 0 can not be accessed in this example. Also note that an equation that defined FS1 to anywhere in the range of 8000h to BFFFh would not be valid. Figure 5 shows the priority levels for all memory components. Any component on a higher level can overlap and has priority over any component on a lower level. Components on the same level must not overlap. Level one has the highest priority and level 3 has the lowest.
26
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Figure 5. Priority Level of Memory and I/O Components
Highest Priority
Level 1 SRAM, I/O
Level 2 Secondary Flash Memory Level 3 Main Flash Memory Lowest Priority
9.1.3.1. Memory Select Configuration for MCUs with Separate Program and Data Spaces The 80C51XA and compatible family of microcontrollers, can be configured to have separate address spaces for code memory (selected using PSEN) and data memory (selected using RD). Any of the memories within the PSD4000 can reside in either space or both spaces. This is controlled through manipulation of the VM register that resides in the PSD's CSIOP space. The VM register is set using PSDsoft to have an initial value. It can subsequently be changed by the microcontroller so that memory mapping can be changed on-the-fly. For example, you may wish to have SRAM and main Flash in Data Space at boot, and secondary Flash memory in Program Space at boot, and later swap main and secondary Flash memory. This is easily done with the VM register by using PSDsoft to configure it for boot up and having the microcontroller change it when desired. Table 11 describes the VM Register.
Table 11. VM Register
Bit 7 PIO_EN
0 = disable PIO mode
Bit 6* Bit 5*
Bit 4 Bit 3 FL_Data Boot_Data
0 = RD can't access Flash 1 = RD access Flash 0 = RD can't access Boot Flash 1 = RD access Boot Flash
Bit 2 FL_Code
0 = PSEN can't access Flash
Bit 1 Bit 0 Boot_Code SRAM_Code
0 = PSEN can't access Boot Flash 0 = PSEN can't access SRAM 1 = PSEN access SRAM
*
*
1= enable PIO mode
*
*
1 = PSEN 1 = PSEN access access Flash Boot Flash
NOTE: Bits 6-5 are not used.
27
PSD4000 Series
Preliminary Information 9.1.3.2 Configuration Modes for MCUs with Separate Program and Data Spaces 9.1.3.2.1 Separate Space Modes Code memory space is separated from data memory space. For example, the PSEN signal is used to access the program code from the main Flash Memory, while the RD signal is used to access data from the secondary Flash memory, SRAM and I/O Ports. This configuration requires the VM register to be set to 0Ch. 9.1.3.2.2 . Combined Space Modes The program and data memory spaces are combined into one space that allows the main Flash Memory, secondary Flash memory, and SRAM to be accessed by either PSEN or RD. For example, to configure the main Flash memory in combined space mode, bits 2 and 4 of the VM register are set to "1". 9.1.3.3 80C51XA Memory Map Example See Application Notes for examples.
The PSD4000 Functional Blocks
(cont.)
Figure 6. 80C51XA Memory Modes - Separate Space Mode
DPLD
RS0 CSBOOT0-3 FS0-7
MAIN FLASH
FLASH BOOT BLOCK
SRAM
CS OE
CS OE
CS OE
PSEN RD
Figure 7. 80C51XA Memory Mode - Combined Space Mode
DPLD
RS0 CSBOOT0-3 FS0-7
MAIN FLASH
FLASH BOOT BLOCK
SRAM
RD
CS OE
CS OE
CS OE
VM REG BIT 3
VM REG BIT 4
PSEN
VM REG BIT 1
VM REG BIT 2
RD
VM REG BIT 0
28
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
9.1.4 Page Register
The eight bit Page Register increases the addressing capability of the microcontroller by a factor of up to 256. The contents of the register can also be read by the microcontroller. The outputs of the Page Register (PGR0-PGR7) are inputs to the PLD decoder and can be included in the Flash Memory, secondary Flash memory, and SRAM chip select equations. If memory paging is not needed, or if not all 8 page register bits are needed for memory paging, then these bits may be used in the PLD for general logic. See Application Notes. Figure 8 shows the Page Register. The eight flip flops in the register are connected to the internal data bus. The microcontroller can write to or read from the Page Register. The Page Register can be accessed at address location CSIOP + E0h.
Figure 8. Page Register
RESET
D0 D1 DATA BUS D2 D3 D4 D5 D6 R/W D7
Q0 Q1 Q2 Q3 Q4 Q5
PGR0 PGR1 PGR2 PGR3 PGR4 PGR5 PGR6 DPLD AND GPLD
INTERNAL SELECTS AND LOGIC
Q6 PGR7 Q7
PAGE REGISTER
FLASH PLD
29
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.1.5 Memory ID Registers
The 8-bit read only memory status registers are included in the CSIOP space. The user can determine the memory configuration of the PSD device by reading the Memory ID0 and Memory ID1 registers. The content of the registers are defined as follow: Memory_ID0 Register Bit 7
S_size 3
Bit 6
S_size 2
Bit 5
S_size 1
Bit 4
S_size 0
Bit 3
F_size 3
Bit 2
F_size 2
Bit 1
F_size 1
Bit 0
F_size 0
Bit Definition F_size3 0 0 0 0 0 0 0 F_size2 0 0 0 0 1 1 1 F_size1 0 0 1 1 0 0 1 F_size0 0 1 0 1 0 1 0 Main Flash Size (Bit) none 256K 512K 1M 2M 4M 8M SRAM Size (Bit) none 16K 32K 64K
S_size3 0 0 0 0 Memory_ID1 Register Bit 7 Bit 6
S_size2 0 0 0 0
S_size1 0 0 1 1
S_size0 0 1 0 1
Bit 5
B_type 1
Bit 4
B_type 0
Bit 3
B_size 3
Bit 2
B_size 2
Bit 1
B_size 1
Bit 0
B_size 0
*
Bit Definition B_size3 0 0 0 0 B_type1 0 0
*
*Not used bit should be set to zero.
B_size2 0 0 0 0 B_type0 0 1
B_size1 0 0 1 1 Boot Block Type Flash EEPROM
B_size0 0 1 0 1
Boot Block Size (Bit) none 128K 256K 512K
30
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
9.2 PLDs
The PLDs bring programmable logic functionality to the PSD4000. After specifying the logic for the PLDs in PSDsoft, the logic is programmed into the device and available upon power-up. The PSD4000 contains two PLDs: the Decode PLD (DPLD), and the General Purpose PLD (GPLD). The PLDs are briefly discussed in the next few paragraphs, and in more detail in sections 9.2.1 and 9.2.2. Figure 10 shows the configuration of the PLDs. The DPLD performs address decoding for internal components, such as memory, registers, and I/O port selects. The GPLD can be used to generate external chip selects, control signals or logic functions. The GPLD has 24 outputs that are connected to Port A, B and C. The AND array is used to form product terms. These product terms are specified using PSDsoft. An Input Bus consisting of 66 signals is connected to the PLDs. The signals are shown in Table 12. The complement of the 66 signals are also available as inputs to the AND array.
Table 12. DPLD and GPLD Inputs Input Source
MCU Address Bus MCU Control Signals Reset Power Down Port A Input Port B Input Port C Input Port D Inputs Port F Inputs Page Register Flash Programming Status Bit
NOTE: The address inputs are A[19:4] in 80C51XA mode.
Input Name
A[15:0]* CNTL[2:0] RST PDN PA[7-0] PB[7-0] PC[7-0] PD[3:0] PF[7:0] PGR(7:0) Rdy/Bsy
Number of Signals
16 3 1 1 8 8 8 4 8 8 1
The Turbo Bit
The PLDs in the PSD4000 can minimize power consumption by switching to standby when inputs remain unchanged for an extended time of about 70 ns. Setting the Turbo mode bit to off (Bit 3 of the PMMR0 register) automatically places the PLDs into standby if no inputs are changing. Turbo-off mode increases propagation delays while reducing power consumption. Refer to the Power Management Unit section on how to set the Turbo Bit. Additionally, five bits are available in the PMMR2 register to block MCU control signals from entering the PLDs. This reduces power consumption and can be used only when these MCU control signals are not used in PLD logic equations.
31
PSD4000 Series
Preliminary Information
Figure 9. PLD Block Diagram
8 DATA BUS
PAGE REGISTER
DECODE PLD
66
8 4 1 1
FLASH MEMORY SELECTS FLASH BOOT MEMORY SELECTS SRAM SELECT CSIOP SELECT
PLD INPUT BUS
GENERAL PURPOSE PLD GPLD
66 PLD OUT 8 PORT A PLD OUT 8 PORT B PLD OUT 8 PORT C
PORT A PLD INPUT PORT B PLD INPUT PORT C PLD INPUT PORT D PLD INPUT
8 8 8 4
PORT D
PORT F PLD INPUT
8
PORT F
32
Preliminary Information
PSD4000 Series 9.2.1 Decode PLD (DPLD) The DPLD, shown in Figure 10, is used for decoding the address for internal components. The DPLD can generate the following decode signals:
The PSD4000 Functional Blocks
(cont.)
* * * *
8 4 1 1
sector selects for the main Flash memory (three product terms each) sector selects for the Secondary Flash memory (three product terms each) internal SRAM select (three product terms) internal CSIOP select (select PSD registers, one product term)
Inputs to the DPLD chip selects may include address inputs, Page Register inputs and other user defined external inputs from Ports A, B, C, D or F. 9.2.2 General Purpose PLD (GPLD) The General Purpose PLD implements user defined system combinatorial logic function or chip selects for external devices. Figure 11 shows how the GPLD is connected to the I/O Ports. The GPLD has 24 outputs and each are routed to a port pin. The port pin can also be configured as input to the GPLD. When it is not used as GPLD output or input, the pin can be configured to perform other I/O functions. All GPLD outputs are identical except in the number of available product terms (PTs) for logic implementation. Select the pin that can best meet the PT requirement of your logic function or chip select. In general, a PT is consumed for each logic "OR" function that you specify in PSDsoft. However, certain logic functions can consume more than one PT even if no logic "OR" is specified (such as specifying an address range with boundaries of high granularity). Table 13 shows the number of "native" PTs for each GPLD output pin. A native PT means that a particular PT is dedicated to an output pin. For example, Table 13 shows that PSD Port A pin PA0 has 3 native product terms. This means a guaranteed minimum of 3 PTs is available to implement logic for that pin. PSD silicon and PSDsoft can include additional PTs beyong the native PTs to implement logic. This is a transparent operation that occurs as needed through PT expansion (internal feedback) or PT allocation (internal borrowing). You may notice in the fitter report generated by PSDsoft that for a given GPLD output pin, more PTs were used to implement logic than the number of native PTs available for that pin. This is because PSDsoft has called on unused PTs from other GPLD output pins to make your logic design fit (PT allocation or PT expansion). For optimum results, choose a GPLD output pin with a large number of native PTs for complicated logic.
Table 13. GPLD Product Term Availability
GPLD Output on Port Pin Port A, Port A, Port B, Port B, Port C, pins pins pins pins pins PA0-3 PA4-7 PB0-3 PB4-7 PC0-7 Number of Native Product Terms 3 9 4 7 1
33
34
3 3 3 3 3 3 (INPUTS) I /O PORTS (PORT A,B,C,F) PGR0 - PGR7 A[15:0] * PD[3:0] (ALE,CLKIN,CSI) PDN (APD OUTPUT) CNTRL[2:0] (READ/WRITE CONTROL SIGNALS) RESET RD_BSY (32) 3 (8) 3 (16) 3 (4) 3 (1) 3 (3) (1) 3 (1) CSIOP RS0 SRAM SELECT I/O DECODER SELECT FS7 8 FLASH MEMORY SECTOR SELECTS 3 CSBOOT 0 CSBOOT 1 CSBOOT 2 CSBOOT 3 4 SECONDARY FLASH MEMORY SECTOR SELECTS FS0
Figure 10. DPLD Logic Array
PSD4000 Series Preliminary Information
*NOTES:
1. The address inputs are A[19:4] in 80C51XA mode. 2. Additional address lines can be brought into PSD via Port A, B, C, C or F.
GENERAL PURPOSE PLD (GPLD)
I/O PORT
AND ARRAY PLD OUTPUT
Preliminary Information
PRODUCT TERM *
PORT A
MUX POLARITY SELECT OTHER I/O FUNCTION PLD INPUT
Figure 11. The MicroCell and I/O Port
PIN PA0-3 HAS 3 NATIVE PTs PIN PA4-7 HAS 9 NATIVE PTs
AND ARRAY PLD OUTPUT
PRODUCT TERM *
PORT B
MUX POLARITY SELECT OTHER I/O FUNCTION PLD INPUT
PLD INPUT BUS
PIN PB0-3 HAS 4 NATIVE PTs PIN PB4-7 HAS 7 NATIVE PTs
AND ARRAY PLD OUTPUT
PRODUCT TERM *
PORT C
MUX POLARITY SELECT OTHER I/O FUNCTION PLD INPUT
PIN PC0-7 HAS 1 NATIVE PT
PSD4000 Series
35
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.3 Microcontroller Bus Interface
The "no-glue logic" PSD4000 Microcontroller Bus Interface can be directly connected to most popular microcontrollers and their control signals. Key 16-bit microcontrollers with their bus types and control signals are shown in Table 14. The MCU interface type is specified using the PSDsoft.
Table 14. Microcontrollers and their Control Signals
MCU 68302, 68306 MMC2001 68330, 68331 68332, 68340 68LC302, MMC2001 68HC16 68HC912 68HC812*** 80196 80196SP 80186 80C161 80C164-80C167 80C51XA H8/3044 M37702M2 CNTL0 R/W R/W WEL R/W R/W R/W WR WRL WR WR WRL WRL R/W CNTL1 LDS DS OE DS E E RD RD RD RD RD RD E SIZ0 LSTRB LSTRB BHE CNTL2 UDS SIZ0 PD3 PD0** AS AS AS AS E ADIO0 - A0 - A0 A0 A0 A0 A0 A0 A0 A4/D0 A0 A0 PF3-PF0
* *
WEH
* * * * * * * * * *
A3-A1 -
*
DBE
* *
WRH
*
ALE ALE ALE ALE ALE AS ALE
*
BHE BHE PSEN
* *
WRH WRH
*
BHE
*
*
***Unused CNTL2 pin can be configured as GPLD input. Other unused pins (PD3-0, PF3-0) can be ***configured for other I/O functions. ***ALE/AS input is optional for microcontrollers with a non-multiplexed bus. ***This configuration is for 68C812A4_EC at 5MHz, 3V only. 9.3.1. PSD4000 Interface to a Multiplexed Bus Figure 16 shows an example of a system using a microcontroller with a 16-bit multiplexed bus and a PSD4000. The ADIO port on the PSD4000 is connected directly to the microcontroller address/data bus. ALE latches the address lines internally. Latched addresses can be brought out to Port E, F or G. The PSD4000 drives the ADIO data bus only when one of its internal resources is accessed and the RD input is active. Should the system address bus exceed sixteen bits, Ports A, B, C, or F may be used as additional address inputs. 9.3.2. PSD4000 Interface to a Non-Multiplexed Bus Figure 17 shows an example of a system using a microcontroller with a 16-bit non-multiplexed bus and a PSD4000. The address bus is connected to the ADIO Port, and the data bus is connected to Port F and G. Port F and G are in tri-state mode when the PSD4000 is not accessed by the microcontroller. Should the system address bus exceed sixteen bits, Ports A, B or C may be used for additional address inputs.
36
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Figure 12. An Example of a Typical 16-Bit Multiplexed Bus Interface
PSD4135G2
MICROCONTROLLER
AD[ 7:0] ADIO PORT PORT F A [ 7: 0] (OPTIONAL)
AD[ 15:8]
PORT G WR RD BHE WR (CNTRL0) RD (CNTRL1) BHE (CNTRL2) RST ALE ALE (PD0) PORT D RESET PORT A,B, or C
A [ 15: 8] (OPTIONAL)
A [ 23:16] (OPTIONAL)
Figure 13. An Example of a Typical 16-Bit Non-Multiplexed Bus Interface
PSD4135G2
D [ 15:0]
MICROCONTROLLER
A [ 15:0]
ADIO PORT
PORT F
D [ 7:0]
PORT G WR RD BHE WR (CNTRL0) RD (CNTRL1) BHE (CNTRL2) RST PORT A,B or C
D[ 15:8] (OPTIONAL)
A[ 23:16] (OPTIONAL)
ALE
ALE (PD0) PORT D
RESET
37
PSD4000 Series
Preliminary Information 9.3.3 Data Byte Enable Reference Microcontrollers have different data byte orientations. The following tables show how the PSD4135G2 interprets byte/word operation in different bus write configurations. Even-byte refers to locations with address A0 equal to zero and odd byte as locations with A0 equal to one. 9.3.4 Microcontroller Interface Examples Figures 14 through 17 show examples of the basic connections between the PSD4135G2 and some popular microcontrollers. The PSD4135G2 Control input pins are labeled as the microcontroller function for which they are configured. The MCU interface is specified using PSDsoft. The PE6 pin should be grounded if Vstby is not used. 9.3.4.1 80C196 and 80C186 In Figure 14, the Intel 80C196 microcontroller, which has a multiplexed sixteen-bit bus, is shown connected to a PSD4135G2. The WR and RD signals are connected to the CNTL0-1 pins. The BHE signal is used for high data byte selection. If BHE is not used, the PSD can be configured to receive the WRL and WRH from the MCU. Higher address inputs (A16-A19) can be routed to Port A, B or C as inputs to the PLD. The AMD 80186 family has the same bus connection to the PSD as the 80C196.
The PSD4000 Functional Blocks
(cont.)
Table 15. 16-Bit Data Bus with BHE BHE
0 0 1
A0
0 1 0
D15-D8
Odd Byte Odd Byte -
D7-D0
Even Byte - Even Byte
Table 16. 16-Bit Data Bus with WRH and WRL WRH
0 0 1
WRL
0 1 0
D15-D8
Odd Byte Odd Byte -
D7-D0
Even Byte - Even Byte
Table 17. 16-Bit Data Bus with SIZ0, A0 (Motorola MCU) SIZ0
0 1 1
A0
0 0 1
D15-D8
Even Byte Even Byte -
D7-D0
Odd Byte - Odd Byte
Table 18. 16-Bit Data Bus with UDS, LDS (Motorola MCU) LDS
0 1 0
UDS
0 0 1
D15-D8
Even Byte Even Byte -
D7-D0
Odd Byte - Odd Byte
38
Preliminary Information
PSD4000 Series 9.3.4.2 MC683XX and 68HC16 Figure 15 shows a Motorola MC68331 with non-multiplexed sixteen-bit data bus and 24-bit address bus. The data bus from the MC68331 is connected to Port F (D0-7) and Port G (D8-D15). The SIZ0 and A0 inputs determine the high/low byte selection. The R/W, DS and SIZ0 are connected to the CNTL0-2 pins. The 68HC16 and other members of the 683XX family have the same connection as the 68331 shown in Figure 15. 9.3.4.3 80C51XA The Philips 80C51XA microcontroller has a 16-bit multiplexed bus with burst cycles. Address bits A[3:1] are not multiplexed while A[19:4] are multiplexed with data bits D[15:0]. The PSD4135G2 supports the 80C51XA burst mode. The WRH signal is connected to the PD3 and the WRL is connected to CNTL0 pin. The RD and PSEN signal is connected to CNTL1-2 pins. Figure 15 shows the XA schematic. The 80C51XA improves bus throughput and performance by issuing Burst cycles to fetch codes from memory. In Burst cycles, addresses A19-4 are latched internally by the PSD, while the 80C51XA drives the A3-1 lines to sequentially fetch up to 16 bytes of code. The PSD access time is then measured from address A3-A1 valid to data in valid. The PSD bus timing requirement in Burst cycle is identical to the normal bus cycle except the address set up or hold time with respect to ALE is not required. 9.3.4.4 H8/300 Figure 16 shows a Hitachi H8/2350 with non-multiplexed sixteen-bit data bus and 24-bit address bus. The H8 data bus is connected to Port F (D0-7) and Port G (D8-15). The WRL, WRH and RD signals are connected to the CNTL0, PD3 and CNTL1 pins respectively. The AS connection is optional and is required if the address are to be latched. 9.3.4.5 MMC2001 The Motorola MCORE MMC2001 microcontroller has a MOD input pin that selects internal or external boot ROM. The PSD4000 can be configured as the external flash boot ROM or as extension to the internal ROM. The MMC2001 has a 16-bit external data bus and 20 address lines with external Chip Select signals. The Chip Select Control Registers allow the user to customize the bus interface and timing to fit the individual system requirement. A typical interface configuration to the PSD4000 is shown in Figure 18. The MMC2001's R/W signal is connected to the cntl0 pin, while EB0 and EB1 (enable byte0 and byte1) are connected to the cntl1 (UDS) and cntl2 (LDS) pins. The WEN bit in the Chip Select Control Register should set to 1 to terminate the EB[0:1] earlier to provide the write data hold time for the PSD. The WSC and WWS bits in the Control Register are set to wait states that meet the PSD access time requirement. Another option is to configure the EB0 and EB1 as WRL and WRH signals. In this case the PSD4000 control setting will be: OE, WRL, WRH where OE is the read signal from the MMC2001. 9.3.4.6 C16X Family The PSD4000 supports Infineon's C16X family of microcontrollers (C161-C167) in both the multiplexed and non-multiplexed bus configuration. In Figure 19 the C167CR is shown connected to the PSD4000 in a multiplexed bus configuration. The control signals from the MCU are WR, RD, BHE and ALE and are routed to the corresponding PSD pins. The C167 has another control signal setting (RD, WRL, WRH, ALE) which is also supported by the PSD4000.
The PSD4000 Functional Blocks
(cont.)
39
40
A[19:16] A[19:16] AD[15:0] AD[15:0]
PSD4000 Series
VCC
80C196NT
PSD4135G2
9 VCC VCC VCC 29 69
67
X1
U3 CRYATAL
66
X2
32
NMI
P3.0/AD0 P3.1/AD1 P3.2/AD2 P3.3/AD3 P3.4/AD4 P3.5/AD5 P3.6/AD6 P3.7/AD7 P4.0/AD8 P4.1/AD9 P4.2/AD10 P4.3/AD11 P4.4/AD12 P4.5/AD13 P4.6/AD14 P4.7/AD15 ADIO8 ADI09 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 22 21 20 19 18 17 16 15 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 13 14 15 16 17 18 19 20 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 21 22 23 24 25 26 27 28
30 29 28 27 26 25 24 23 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 3 4 5 6 7 10 11 12 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 31 32 33 34 35 36 37 38
58 59 60 61
P6.0/EPA8 P6.1EPA9 P6.2/T1CLK P6.3/T1DIR
44 45 46 47 A16 A17 A18 A19 WR 59 60 CRTL0 (WR) CNTL1 (RD) CNTL2 (BHE) 40 RD BHE EP.0/A16 EP.1/A17 EP.2/A18 EP.3/A19 WR/WRL/P5.2 RD/P5.3 BHE/WRH/P5.5 4 RESET 39 ALE 8 79 80 1 2 PDO (ALE) PD1 (CLKIN) PD2 (CSI) PD3 (WRH) 14 13 12 11 9 7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7
Figure 14. Interfacing the PSD4135G2 with an 80C196
ACH4/P0.4/PMD.0 ACH5/P0.5/PMD.1 ACH6/P0.6/PMD.2 ACH7/P0.7/PMD.3
36 37 38 39 40 41 42 43 ALE/ADV/P5.0 31
P2.0/TX/PVR P2.1/RXD/PALE P2.2/EXINT/PROG P2.3/INTB P2.4/INTINTOUT P2.5/HLD P2.6/HLDA/CPVER P2.7/CLKOUT/PAC
51 52 53 54 55 56 57 58
62 63 54 65 RESET RESET
P6.4/SC0 P6.5/6D0 P6.6/SC1 P6.7/SD1
49 6 48 READY/P5.6 EA VCC BUSWIDTH/P5.7 INST/P5.1 SLPINT/P5.4 1 10 3 33 2
VREF VPP ANGND
PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 71 72 73 74 75 76 77 78 PEO (TMS) PE1 (TCK/ST) PE2 (TDI) PD2 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 GND GND GND GND GND 8 30 49 50 70
61 62 63 64 65 66 67 68 41 42 43 44 45 46 47 48 A16 A17 A18 A19
50 57 56 55 54 53 52 51
P1.7/EPA7 P1.0/EPAQ/T2CLK P1.1/EPA1 P1.2/EPA2/T2DIR P1.3/EPA3 P1.4/EPA4 P1.5/EPA5 P1.6/EPA6
Preliminary Information
RESET
D[15:0] D[15:0] A[23:0] VCC A[23:0]
Preliminary Information
MC68331 PSD4135G2
9 VCC VCC VCC PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 21 22 23 24 25 26 27 28 D8 D9 D10 D11 D12 D13 D14 D15 31 32 33 34 35 36 37 38 D0 D1 D2 D3 D4 D5 D6 D7 29 69 A0 A1 A2 A3 A4 A5 A6 A7 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 ADIO8 ADIO9 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 A8 A9 A10 A11 A12 A13 A14 A15 13 14 15 16 17 18 19 20 90 20 21 22 23 24 25 26 A0 A1 A2 A3 A4 A5 A6 A7 3 4 5 6 7 10 11 12
D0 D1 D2 D3 D4 D5 D6 D7
111 110 109 108 105 104 103 102
D0 D1 D2 D3 D4 D5 D6 D7
D8 D9 D10 D11 D12 D13 D14 D15
100 99 98 97 94 93 92 91
D8 D9 D10 D11 D12 D13 D14 D15
Figure 15. Interfacing the PSD4135G2 with an MC68331
A16 A17 A18 A19 A20 A21 A22 A23 R/W 59 60 CRTL0 (R/W) CNTL1 (DS) CNTL2 (SIZ0) SIZ0 40 DS AS
89 88 SIZ0 AS RESET 68 RESET 82 81 79 80 1 2 39
DSACK0 DSACK1
A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19_CS6 A20_CS7 A21_CS8 A22_CS9 A23_CS10 R_W DS PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PD0 (AS) PD1 (CLKIN) PD2 (CSI) PD3 RESET 51 52 53 54 55 56 57 58 61 62 63 64 65 66 67 68
27 30 31 32 33 35 36 37 38 41 42 121 122 123 124 125 79 85
77 76 75 74 73 72 71 SIZ1 CLKOUT 66 80
IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7
71 72 73 74 75 76 77 78
PE0 (TMS) PE1 (TCK/ST) PE2 (TDI) PD3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) GND GND GND GND GND 8 30 49 50 70
CSBOOT BR_CSO BG_CS1 BGACK_CS2 FCO_CS3 FC1_CS4 FC2_CS5
112 113 114 115 118 119 120
PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7
41 42 43 44 45 46 47 48
A16 A17 A18 A19
RESET
RESET
PSD4000 Series
41
42
D[15:0] D[15:0] A[3:1] A[3:1] VCC
PSD4000 Series
XA-G3
VCC VCC VCC
PSD4135G2
9 29 69
21 A1 A2 A3
XTAL1
CRYATAL
20
XTAL2
11 RXD0 13 TXD0 6 RXD1 7 TXD1 A12D8 A13D9 A14D10 A15D11 A16D12 A17D13 A18D14 A19D15 ADIO8 ADI09 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 24 25 26 27 28 29 30 31 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 A12D8 A13D9 A14D10 A15D11 A16D12 A17D13 A18D14 A19D15 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
A4D0 A5D1 A6D2 A7D3 A8D4 A9D5 A10D6 A11D7
43 42 41 40 39 38 37 36 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7
A4D0 A5D1 A6D2 A7D3 A8D4 A9D5 A10D6 A11D7 3 4 5 6 7 10 11 12
31 32 33 34 35 36 37 38
9 T2EX 8 T2 10 T0
RESET WRL 59 60 CRTL0 (WR) CNTL1 (RD) CNTL2 40
VCC RD PSEN
10 14 15
RST INT0 INT1
Figure 16. Interfacing the PSD4135G2 with a 80C51XA-G3
35 PSEN 33 WRH 39 RESET ALE 32
EA/WAIT 79 80 1 2
A3 A2 A1 A0/WRH WRL RD
5 4 3 2 18 19 A3 A2 A1
17 ALE
BUSW
PD0 (ALE) PD1 (CLKIN) PD2 (CSI) PD3 (WRH)
PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7
51 52 53 54 55 56 57 58 61 62 63 64 65 66 67 68
RESET
71 72 73 74 75 76 77 78
PEO (TMS) PE1 (TCK/ST) PE2 (TDI) PD3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) GND GND GND GND GND 8 30 49 50 70
PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7
41 42 43 44 45 46 47 48
Preliminary Information
D[15:0] A[23:0] A[23:0] VCC D[15:0]
H85/2350
9 VCC VCC VCC ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 ADIO8 ADIO9 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 21 22 23 24 25 26 27 28 D8 D9 D10 D11 D12 D13 D14 D15 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 31 32 33 34 35 36 37 38 D0 D1 D2 D3 D4 D5 D6 D7 29 69 PC0/A0 PC1/A1 PC2/A2 PC3/A3 PC4/A4 PC5/A5 PC6/A6 PC7/A7 A8 A9 A10 A11 A12 A13 A14 A15 13 14 15 16 17 18 19 20 2 3 4 5 7 8 9 10 A0 A1 A2 A3 A4 A5 A6 A7 3 4 5 6 7 10 11 12
Preliminary Information
PSD4135G2
D0 D1 D2 D3 D4 D5 D6 D7
34 35 36 37 39 40 41 42
PE0/D0 PE0/D1 PE0/D2 PE0/D3 PE0/D4 PE0/D5 PE0/D6 PE0/D7
D8 D9 D10 D11 D12 D13 D14 D15
43 44 45 46 48 49 50 51
PD0/D8 PD1/D9 PD2/D10 PD3/D11 PD4/D12 PD5/D13 PD6/D14 PD7/D15
78 WRL 59 60 CRTL0 (WRL) CNTL1 (RD) CNTL2 40 RD AS WRH RESET 39 RESET 79 80 1 2 PDO (AS) PD1 (CLKIN) PD2 (CSI) PD3 (WRH)
EXTAL
U3 CRYATAL
77
XTAL
PB0/A8 PB1/A9 PB2/A10 PB3/A11 PB4/A12 PB5/A13 PB6/A14 PB7/A15 PA0/A16 PA1/A17 PA2/A18 PB3/A19 PA4/A20/IRQ4 PA5/A21/IRQ5 PA6/A22/IRQ6 PA7/A23/1RQ7 LWR RD A16 A17 A18 A19 A20 A21 A22 A23 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 51 52 53 54 55 56 57 58 AS HWR RESET WDTOVF STBY 112 111 110 109 108 107 106 105 95 96 97 98 99 100 101 102 92 75 71 72 73 74 75 76 77 78 72 PE0 (TMS) PE1 (TCK/ST) PE2 (TDI) PD3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) GND GND GND GND GND 8 30 49 50 70 73 84 82 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 61 62 63 64 65 66 67 68 41 42 43 44 45 46 47 48 A16 A17 A18 A19
Figure 17. Interfacing a PSD4135G2 with a H83/2350
29 30 31 32
CS7/IRQ3 CS6/IRQ2 IRQ1 IRQ0
11 12 13 14 16 17 18 19 20 21 22 23 25 26 27 28 85 83
55 53 57 56 54 58 90 89 91 PO8/TIOCA0/DACK PO9/TIOCB0/DACK PO10/TIOCC0/TCL PO11/TIOCD0/TCL PO12/TIOCA1 PO13/TIOCB1/TCL PO14/TIOCA2 PO15/TIOCB2/TCL AN0 AN1 AN2 AN3 AN4 AN5 AN6/DA0 AN7/DA1 ADTRG PG0/CAS/OE PG1/CS3 PG2/CS2 PG3/CS1 PG4/CS0 116 117 118 119 120
RXD0 TXD0 SCK0 PXD1 TXD1 SCK1 RXD2 TXD2 SCK2
88 87 86 74 71 70 69 68 67 66 65 64 60 61 62 63
PF0/BREQ PF1/BACK PF2/LCAS/WAIT/B NMI PO0/TIOCA3 PO1/TIOCB3 PO2/TIOC3/TMRI PO3/TIOCD3/TMCI PO4/TIOCA4/TMRI PO5/TIOB4/TMRC PO6/TI0C5/TMRO PO7/TIOCB5/TMRO DREQ/CS4 TEND0/CS5 DREQ1 TEND1
113 114 115
MOD0 MOD1 MOD2
80
PF0/PHI0 RESET
RESET
PSD4000 Series
43
GVDD0 GGND0
GVDD1 GGND1
HVDD HGND
99 98
110 111
122 123
Preliminary Information
RESET
RESET
127 133 134 137 138
QVCCH QVCC QGND JVDD JGND
44
D[15:0] D[15:0] A[21:0] A[21:0] VCC
PSD4000 Series
UI
9 VCC VCC VCC ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 ADIO8 ADIO9 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 21 22 23 24 25 26 27 28 D8 D9 D10 D11 D12 D13 D14 D15 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 31 32 33 34 35 36 37 38 D0 D1 D2 D3 D4 D5 D6 D7 29 69 U3 CRYATAL EXOSC XSOC DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 A8 A9 A10 A11 A12 A13 A14 A15 13 14 15 16 17 18 19 20 ADDR0 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 15 D0 D1 D2 D3 D4 D5 D6 D7 22 23 24 25 28 29 30 31 42 43 44 45 50 51 52 53 A0 A1 A2 A3 A4 A5 A6 A7 3 4 5 6 7 10 11 12 14
U2
D8 D9 D10 D11 D12 D13 D14 D15 32 33 34 35 38 39 40 41 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15
135 136 TXD1/SIZ0 RXD1/SIZ1 UDS R/W LDS CSO* RESET 39 RESET 79 80 1 2 PD0 (AS) PD1 (CLKIN) PD2 (CSI) PD3 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 A16* A17 A18 A19 TXD0/PSTAT0 RXD0/PSTAT1 RTS0/PSTAT2 CTS0/PSTAT3 R/W OE EB1 EB0 CS0 CS1 CS2 CS3 75 76 79 80 SPI_MISO SPI_MISI SPI_EN SPI_CLK SPI_GP PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 ROW7 ROW6 ROW5 ROW4 ROW3 ROW2 ROW1 ROW0 73 74 82 81 CNTL2 (UDS) 40 129 130 131 132 121 124 125 126 128 139 140 141 142 143 144 113 114 115 116 117 118 119 120 GND GND GND GND GND 8 30 49 50 70 103 104 105 106 107 108 109 112 92 91 90 78 77 68 67 58 59 36 37 26 27 19 20 55 21 QVCC QVCCH QVCCH QGND NOT USED AGND0 QGND QVCC 12 46 47 48 93 94 95 96 97 100 101 102 INT7 INT6 INT5 INT4 INT3 INT2 INT1 INT0 DE TDO TMS TD1 TCK TRST TEST QVCC QVCCH QGND CVDD CGND AVDD2 AGND2 AVDD1 AGND1 DVDD1 DGMD1 DVDD0 DGND0 IF GPS_OUT FVDD FGND CLKOUT CLKIN RSTOUT RSTIN LVRSTIN VBATT VSTBY COL7 COL6 COL5 COL4 COL3 COL2 COL1 COL0 84 83 85 86 87 88 89 1 2 3 6 4 5 7 8 9 10 11
ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 ADDR17 ADDR18 ADDR19 ADDR20 ADDR21
54 56 57 60 61 62 63 64 65 66 69 70 71 72
PSD4135G2
59 60 CRTL0 (R/W) CNTL1 (LDS)
A16 A17 A18 A19 A20 A21 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 51 52 53 54 55 56 57 58
Figure 18. Interfacing a PSD4135G2 with a MMC2001
MMC2001
71 72 73 74 75 76 77 78 PE0 (TMS) PE1 (TCK/ST) PE2 (TDI) PE3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON)
17 18 13 16 MOD XVDD XGND XGND
A[19:16] A[19:16] AD[15:0] VCC VCC AD[15:0]
144 136 129 109 93
9 VCC VCC VCC 29 69 138 XTAL1 VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC
82 72 56 46 17
U3 CRYATAL 137 XTAL2
Preliminary Information
AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 ADIO8 ADI09 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 108 111 112 113 114 115 116 117 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 13 14 15 16 17 18 19 20 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 21 22 23 24 25 26 27 28
65 66 67 68 69 70 73 74 75 76 77 78 P3.0/T0IN P3.1/T6OUT P3.2/CAPIN P3.4/T3TOUT P3.4/T3EUD P3.5/T4IN P3.6/T3IN P3.7/T2IN P3.8/MRST P3.10/TXD0 P3.10/TXD0 P3.11/RXD0 80 81 P3.13/SCLK P3.15/CLKOUT 59 60 CRTL0 (WR) CNTL1 (RD) CNTL2 (BHE) BHE 40 ALE WR RD 79 80 1 2 PDO (ALE) PD1 (CLKIN) PD2 (CSI) PD3 (WRH)
100 101 102 103 104 105 106 107 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 3 4 5 6 7 10 11 12 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7
31 32 33 34 35 36 37 38
C167CR
P4.0/A16 A17 A18 A19 A20 A21 A22 P4.7/A23 WR/WRL RD P312/BHE/WRH ALE EA RESET 99 39 RESET PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 GND GND GND GND GND 8 30 49 50 70 61 62 63 64 65 66 67 68 41 42 43 44 45 46 47 48 85 86 87 88 89 90 91 92 96 95 79 98 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 A16 A17 A18 A19 51 52 53 54 55 56 57 58
Figure 19. Interfacing a PSD4135G2 with a C167R
PSD4135G2
27 28 29 30 31 32 33 34 35 36 39 40 41 43 44 P5.0/AN0 P5.1/AN1 P5.2/AN2 P5.3/AN3 P5.4/AN4 P5.5/AN5 P5.6/AN6 P5.7/AN7 P5.9/AN8 P5.9/AN9 P5.10/AN10/T6UED P5.11/AN11/T5UED P5.12/AN12/T6IN P5.14/AN14/T4UED P5.15/AN15/T2UED P6.0/ CSO P6.1/ CS1 P6.2/ CS2 P6.3/ CS3 P6.4/ CS4 P6.5/ HOLD P6.6/ HLDA P6.7/ BREQ P7.0/POUT0 P7.1/POUT1 P7.2/POUT2 P7.3POUT/3 P7.4/CC28IO P7.5/CC29IO P7.6/CC30IO P7.7/CC31IO P8.0/CC16IO P8.1/CC17IO P8.2/CC18IO P8.3/CC19IO P8.4/CC20IO P8.5/CC21IO P8.6/CC22IO P8.7/CC23IO Vref READY P2.0/CC0IO P2.1/CC1IO P2.2/CC2IO P2.3/CC3IO P2.4/CC4IO P2.5/CC5IO P2.6/CC6IO P2.7/CC7IO P2.8/CC8IO/EX0IN P2.9/CC9IO/EX1IN P2.10CC10IO/EX2IN P2.11/CC11IO/EX3IN P2.12/CC12IO/EX4IN P2.13/CC13IO/EX5IN P2.14/CC14IO/EX6IN P2.15/CC15IO/EX7IN 140 141 142 RSTIN RSTOUT NMI VSS VSS VSS VSS VSS 143 139 127 110 94 83 71 55 VSS VSS VSS VSS VSS 45 18 AGND 38 47 48 49 50 51 52 53 54 57 58 59 60 61 62 63 64 P1H7 P1H6 P1H5 P1H4 P1H3 P1H2 P1H1 P1H0 P1L7 P1L6 P1L5 P1L4 P1L3 P1L2 P1L1 P1L0 71 72 73 74 75 76 77 78 PEO (TMS) PE1 (TCK/ST) PE2 (TDI) PD2 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) 135 134 133 132 131 130 129 128 125 124 123 122 121 120 119 118 1 2 3 4 5 6 7 8 19 20 21 22 23 24 25 26 9 10 11 12 13 14 15 16
A16 A17 A18 A19
37 97
RESET
RESET
PSD4000 Series
45
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.4 I/O Ports
There are seven programmable I/O ports: Ports A, B, C, D, E, F and G. Each of the ports is eight bits except Port D, which is 4 bits. Each port pin is individually user configurable, thus allowing multiple functions per port. The ports are configured using PSDsoft or by the microcontroller writing to on-chip registers in the CSIOP address space. The topics discussed in this section are: * General Port Architecture * Port Operating Modes * Port Configuration Registers * Port Data Registers * Individual Port Functionality. 9.4.1 General Port Architecture The general architecture of the I/O Port is shown in Figure 20. Individual Port architectures are shown in Figures 21 through 23. In general, once the purpose for a port pin has been defined, that pin will no longer be available for other purposes. Exceptions will be noted. As shown in Figure 20, the ports contain an output multiplexer whose selects are driven by the configuration bits in the Control Registers (Ports E, F and G only) and PSDsoft Configuration. Inputs to the multiplexer include the following: t Output data from the Data Out Register t Latched address outputs t GPLD outputs (External Chip Selects) The Port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be read. The PDB is connected to the Internal Data Bus for feedback and can be read by the microcontroller. The Data Out and MicroCell outputs, Direction and Control Registers, and port pin input are all connected to the PDB. The contents of these registers can be altered by the microcontroller. The PDB feedback path allows the microcontroller to check the contents of the registers. 9.4.2 Port Operating Modes The I/O Ports have several modes of operation. Some modes can be defined using PSDsoft, some by the microcontroller writing to the Registers in CSIOP space, and some by both. The modes that can only be defined using PSDsoft must be programmed into the device and cannot be changed unless the device is reprogrammed. The modes that can be changed by the microcontroller can be done so dynamically at run-time. The PLD I/O, Data Port, Address Input, and MCU Reset modes are the only modes that must be defined before programming the device. All other modes can be changed by the microcontroller at run-time. Table 16 summarizes which modes are available on each port. Table 19 shows how and where the different modes are configured. Each of the port operating modes are described in the following subsections.
46
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Table 16. Port Operating Modes
Port Mode
MCU I/O PLD Outputs PLD Inputs Address Out
Port A
Yes Yes Yes No
Port B
Yes Yes Yes No
Port C
Yes Yes Yes No
Port D
Yes No Yes No
Port E
Yes No No Yes (A7-0)
Port F
Yes No Yes Yes (A7-0)
Port G
Yes No No Yes (A7-0) or (A15-8) No Yes No Yes
Address In Data Port JTAG ISP MCU Reset Mode*
Yes No No No
Yes No No No
Yes No No No
Yes No No No
No No Yes No
Yes Yes No Yes
*Available to Motorola 16-bit 683XX and HC16family of MCUs.
Figure 20. General I/O Port Architecture
PORT PIN
OUTPUT MUX
DATA OUT
ADDRESS
OUTPUT SELECT
DATA IN
CONTROL REG.
DATA OUT REG.
READ MUX
DIR REG.
Q
Q
Q
D
B
P
G
D
D
ADDRESS
GPLD OUTPUTS
D
WR
D WR
ALE
WR
Q
PLD INPUT INTERNAL DATA BUS
47
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
Table 17. Port Operating Mode Settings
Defined In PSDsoft
Declare pins only Declare pins and logic or chip select equations Selected for MCU with non-mux bus Declare pins only Declare pins NA Declare pins only Specify pin logic level NA NA NA NA NA NA NA NA
Mode
MCU I/O
Control Register Setting
0 (Note 1) NA
Direction Register Setting
1 = output, 0 = input
VM Register Setting
NA NA
PLD I/O
Data Port (Port F, G) Address Out (Port E, F, G) Address In (Port A,B,C,D,F) JTAG ISP MCU Reset Mode
NA
NA
NA
1
1
NA
*NA = Not Applicable
NOTE: 1. Control Register setting is not applicable to Ports A, B and C.
9.4.2.1 MCU I/O Mode In the MCU I/O Mode, the microcontroller uses the PSD4000 ports to expand its own I/O ports. By setting up the CSIOP space, the ports on the PSD4000 are mapped into the microcontroller address space. The addresses of the ports are listed in Table 6. A port pin can be put into MCU I/O mode by writing a `0' to the corresponding bit in the Control Register (Port E, F and G). The MCU I/O direction may be changed by writing to the corresponding bit in the Direction Register. See the subsection on the Direction Register in the "Port Registers" section. When the pin is configured as an output, the content of the Data Out Register drives the pin. When configured as an input, the microcontroller can read the port input through the Data In buffer. See Figure 20. Ports A, B and C do not have Control Registers, and are in MCU I/O mode by default. They can be used for PLD I/O if they are specified in PSDsoft. 9.4.2.2 PLD I/O Mode The PLD I/O Mode uses a port as an input to the CPLD's Input MicroCells, and/or as an output from the GPLD. The corresponding bit in the Direction Register must not be set to `1' if the pin is defined as a PLD input pin in PSDsoft. The PLD I/O Mode is specified in PSDsoft by declaring the port pins, and then specifying an equation in PSDsoft.
48
Preliminary Information
PSD4000 Series 9.4.2.3 Address Out Mode For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used to drive latched addresses onto the port pins. These port pins can, in turn, drive external devices. Either the output enable or the corresponding bits of both the Direction Register and Control Register must be set to a `1' for pins to use Address Out Mode. This must be done by the MCU at run-time. See Table 18 for the address output pin assignments on Ports E, F and F for various MCUs. Note: Do not drive address lines with Address Out Mode to an external memory device if it is intended for the MCU to boot from the external device. The MCU must first boot from PSD memory so the Direction and Control register bits can be set.
The PSD4000 Functional Blocks
(cont.)
Table 18. I/O Port Latched Address Output Assignments
MCU
80C51XA All Other MCU with Multiplexed Bus
Port E (3:0)
N/A
Port E (7:4)
Addr (7:4)
Port F (3:0)
N/A
Port F (7:4)
Addr (7:4)
Port G (3:0)
Addr (11:8)
Port G (7:4)
Addr (15:12)
Addr (3:0)
Addr (7:4)
Addr (3:0)
Addr (7:4)
Addr (11:8)
Addr (15:12)
9.4.2.4 Address In Mode For microcontrollers that have more than 16 address lines, the higher addresses can be connected to Ports A, B, C, D or F and are routed as inputs to the PLDs. The address input can be latched by the address strobe (ALE/AS). Any input that is included in the DPLD equations for the Main Flash, Boot Flash, or SRAM is considered to be an address input. 9.4.2.5 Data Port Mode Port F and G can be used as a data bus port for a microcontroller with a non-multiplexed address/data bus. The Data Port is connected to the data bus of the microcontroller. The general I/O functions are disabled in Port F and G if the ports are configured as Data Port. Data Port Mode is automatically configured in PSDsoft when a non-multiplexed bus MCU is selected. 9.4.2.6 JTAG ISP Port E is JTAG compliant, and can be used for In-System Programming (ISP). 9.4.2.7 MCU Reset Mode Port F and G can be configured to operate in "MCU Reset" mode. This mode is available when PSD is configured for the Motorola 16-bit 683XX and HC16 family and is active only during reset. At the rising edge of the Reset input, the MCU reads the logic level on the Data Bus D15-0 pins. The MCU then configures some of its I/O pin functions according to the logic level input on the data bus lines. Two dedicated buffers are usually enabled during reset to drive the data bus lines to the desired logic level. The PSD4135G2 can replace the two buffers by configuring Port F and G to operate in MCU Reset Mode. In this mode, the PSD will drive the pre-defined logic level or data pattern onto the MCU Data Bus when reset is active and there is no ongoing bus cycle. After reset, Port F and G return to the normal Data Port Mode. The MCU Reset Mode is enabled and configured in PSDsoft. The user defines the logic level (data pattern) that will be driven out from Port F and G during reset.
49
PSD4000 Series
Preliminary Information 9.4.3 Port Configuration Registers (PCRs) Each port has a set of PCRs used for configuration. The contents of the registers can be accessed by the microcontroller through normal read/write bus cycles at the addresses given in Table 6. The addresses in Table 6 are the offsets in hex from the base of the CSIOP register. The pins of a port are individually configurable and each bit in the register controls its respective pin. For example, Bit 0 in a register refers to Bit 0 of its port. The three PCRs, shown in Table 19, are used for setting the port configurations. The default power-up state for each register in Table 22 is 00h.
The PSD4000 Functional Blocks
(cont.)
Table 19. Port Configuration Registers Register Name
Control Direction Drive Select* *NOTE:
Port
E,F,G A,B,C,D,E,F,G A,B,C,D,E,F,G
MCU Access
Write/Read Write/Read Write/Read
See Table 22 for Drive Register bit definition.
9.4.3.1 Control Register Any bit set to `0' in the Control Register sets the corresponding Port pin to MCU I/O Mode, and a `1' sets it to Address Out Mode. The default mode is MCU I/O. Only Ports E, F and G have an associated Control Register. 9.4.3.2 Direction Register The Direction Register controls the direction of data flow in the I/O Ports. Any bit set to `1' in the Direction Register will cause the corresponding pin to be an output, and any bit set to `0' will cause it to be an input. The default mode for all port pins is input. Figures 21 and 23 show the Port Architecture diagrams for Ports A/B/C and E/F/G respectively. The direction of data flow for Ports A, B, C and F are controlled by the direction register. An example of a configuration for a port with the three least significant bits set to output and the remainder set to input is shown in Table 21. Since Port D only contains four pins, the Direction Register for Port D has only the four least significant bits active.
Table 20. Port Pin Direction Control Direction Register Bit Port Pin Mode
0 1 Input Output
Table 21. Port Direction Assignment Example
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 1 Bit 1 1 Bit 0 1
50
Preliminary Information
PSD4000 Series 9.4.3.3 Drive Select Register The Drive Select Register configures the pin driver as Open Drain or CMOS for some port pins, and controls the slew rate for the other port pins. An external pull-up resistor should be used for pins configured as Open Drain. A pin can be configured as Open Drain if its corresponding bit in the Drive Select Register is set to a `1'. The default pin drive is CMOS. Aside: the slew rate is a measurement of the rise and fall times of an output. A higher slew rate means a faster output response and may create more electrical noise. A pin operates in a high slew rate when the corresponding bit in the Drive Register is set to `1'. The default rate is slow slew. Table 22 shows the Drive Register for Ports A, B, C, D, E, F and G. It summarizes which pins can be configured as Open Drain outputs and which pins the slew rate can be set for.
The PSD4000 Functional Blocks
(cont.)
Table 22. Drive Register Pin Assignment
Drive Register Port A Port B Port C Port D Port E Port F Port G Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain Bit 7 Open Drain Open Drain Slew Rate Bit 6 Open Drain Open Drain Slew Rate Bit 5 Open Drain Open Drain Slew Rate Bit 4 Open Drain Open Drain Slew Rate Bit 3 Open Drain Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain Bit 2 Open Drain Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain Bit 1 Open Drain Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain Bit 0 Open Drain Open Drain Slew Rate Open Drain Open Drain Slew Rate Open Drain
9.4.4 Port Data Registers
The Port Data Registers, shown in Table 23, are used by the microcontroller to write data to or read data from the ports. Table 23 shows the register name, the ports having each register type, and microcontroller access for each register type. The registers are described below. 9.4.4.1 Data In Port pins are connected directly to the Data In buffer. In MCU I/O input mode, the pin input is read through the Data In buffer. 9.4.4.2 Data Out Register Stores output data written by the MCU in the MCU I/O output mode. The contents of the Register are driven out to the pins if the Direction Register or the output enable product term is set to "1". The contents of the register can also be read back by the microcontroller.
Table 27. Port Data Registers Register Name
Data In Data Out
Port
A,B,C,D,E,F,G A,B,C,D,E,F,G
MCU Access
Read - input on pin Write/Read
51
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.4.5 Ports A, B and C - Functionality and Structure
Ports A and B have similar functionality and structure, as shown in Figure 21. The two ports can be configured to perform one or more of the following functions:
t t t t t
MCU I/O Mode GPLD Output - Combinatorial PLD outputs. PLD Input - Input to the PLDs. Address In - Additional high address inputs may be latched by ALE. Open Drain/Slew Rate - pins PC[7:0]can be configured to fast slew rate, pins PA[7:0] and PB[7:0] can be configured to Open Drain Mode.
Figure 21. Port A, B and C
DATA OUT REG. D WR PORT PIN OUTPUT MUX GPLD OUTPUT READ MUX Q DATA OUT
INTERNAL DATA BUS
P D B DATA IN
OUTPUT SELECT
DIR REG. D WR PLD INPUT Q
52
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
9.4.6 Port D - Functionality and Structure
Port D has four I/O pins. See Figure 22. Port D can be configured to program one or more of the following functions:
t MCU I/O Mode t PLD Input - direct input to PLD
Port D pins can be configured in PSDsoft as input pins for other dedicated functions:
t PD0 - ALE, as address strobe input t PD1 - CLKIN, as clock input to the PLD and APD counter t PD2 - CSI, as active low chip select input. A high input will disable the
Flash/SRAM and CSIOP.
t PD3 - WRH, as active low Write Enable (high byte) input or as DBE input from
68HC912
9.4.7 Port E - Functionality and Structure
Port E can be configured to perform one or more of the following functions (see Figure 23):
t MCU I/O Mode t In-System Programming - JTAG port can be enabled for programming/erase of the
PSD4000 device. (See Section 9.6 for more information on JTAG programming.) Pins that are configured as JTAG pins in PSDsoft will not be available for other I/O functions. Open Drain - Port E pins can be configured in Open Drain Mode Battery Backup features - PE6 can be configured as a Battery Input (Vstby) pin. PE7 can be configured as a Battery On Indicator output pin, indicating when Vcc is less than Vbat. Latched Address Output - Provided latched address (A7-0) output
t t t
Figure 22. Port D Structure
DATA OUT REG. DATA OUT D WR OUTPUT MUX Q PORT D PIN
INTERNAL DATA BUS
READ MUX
P D B DATA IN
OUTPUT SELECT
DIR REG. D WR Q PLD INPUT
53
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.4.8 Port F - Functionality and Structure
Port F can be configured to perform one or more of the following functions:
t t t t t t t
MCU I/O Mode PLD Input - as direct input ot the PLD array. Address In - additional high address inputs. Direct input to the PLD array. Latched Address Out - Provide latched address out per Table 29. Slew Rate - pins can be set up for fast slew rate. Data Port - connected to D[7:0] when Port F is configured as Data Port for a non-multiplexed bus. MCU Reset Mode - for 16-bit Motorola 683XX and HC16 microcontrollers.
9.4.9 Port G - Functionality and Structure
Port G can be configured to perform one or more of the following functions:
t t t t t
MCU I/O Mode Latched Address Out - provide latched address out per Table 29. Open Drain - pins can be configured in Open Drain Mode Data Port - connected to D[15:8] when Port G is configured as Data Port for a non-multiplexed bus. MCU Reset Mode - for 16-bit Motorola 683XX and HC16 microcontrollers
Figure 23. Ports E, F and G Structure
DATA OUT REG. D WR ADDRESS ALE D G Q ADDRESS A[ 7:0] OR A[15:8] OUTPUT MUX PORT PIN Q
DATA OUT
INTERNAL DATA BUS
READ MUX P D B CONTROL REG. D WR DIR REG. D WR Q Q DATA IN OUTPUT SELECT
PLD INPUT (PORT F) ISP OR BATTERY BACK-UP (PORT E) CONFIGURATION BIT
54
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
9.5 Power Management
The PSD4000 offers configurable power saving options. These options may be used individually or in combinations, as follows:
t All memory types in a PSD (Flash, Secondary Flash, and SRAM) are built with
Zero-Power technology. In addition to using special silicon design methodology, Zero-Power technology puts the memories into standby mode when address/data inputs are not changing (zero DC current). As soon as a transition occurs on an input, the affected memory "wakes up", changes and latches its outputs, then goes back to standby. The designer does not have to do anything special to achieve memory standby mode when no inputs are changing--it happens automatically. The PLD sections can also achieve standby mode when its inputs are not changing, see PMMR registers below.
t Like the Zero-Power feature, the Automatic Power Down (APD) logic allows the PSD to
reduce to standby current automatically. The APD will block MCU address/data signals from reaching the memories and PLDs. This feature is available on all PSD4000 devices. The APD unit is described in more detail in section 9.5.1. Built in logic will monitor the address strobe of the MCU for activity. If there is no activity for a certain time period (MCU is asleep), the APD logic initiates Power Down Mode (if enabled). Once in Power Down Mode, all address/data signals are blocked from reaching PSD memories and PLDs, and the memories are deselected internally. This allows the memories and PLDs to remain in standby mode even if the address/data lines are changing state externally (noise, other devices on the MCU bus, etc.). Keep in mind that any unblocked PLD input signals that are changing states keeps the PLD out of standby mode, but not the memories.
t The PSD Chip Select Input (CSI) can be used to disable the internal memories,
placing them in standby mode even if inputs are changing. This feature does not block any internal signals or disable the PLDs. This is a good alternative to using the APD logic, especially if your MCU has a chip select output. There is a slight penalty in memory access time when the CSI signal makes its initial transition from deselected to selected.
t The PMMR registers can be written by the MCU at run-time to manage power. All PSD
devices support "blocking bits" in these registers that are set to block designated signals from reaching both PLDs. Current consumption of the PLDs is directly related to the composite frequency of the changes on their inputs (see Figures 27 and 27a). Significant power savings can be achieved by blocking signals that are not used in PLD logic equations at run time. PSDsoft creates a fuse map that automatically blocks the low address byte (A7-A0) or the control signals (CNTL0-2, ALE and WRH/DBE) if none of these signals are used in PLD logic equations. The PSD4000 devices have a Turbo Bit in the PMMR0 register. This bit can be set to disable the Turbo Mode feature (default is Turbo Mode on). While Turbo Mode is disabled, the PLDs can achieve standby current when no PLD inputs are changing (zero DC current). Even when inputs do change, significant power can be saved at lower frequencies (AC current), compared to when Turbo Mode is enabled. Conversely, when the Turbo Mode is enabled, there is a significant DC current component and the AC component is higher. 9.5.1 Automatic Power Down (APD) Unit and Power Down Mode The APD Unit, shown in Figure 24, puts the PSD into Power Down Mode by monitoring the activity of the address strobe (ALE/AS). If the APD unit is enabled, as soon as activity on the address strobe stops, a four bit counter starts counting. If the address strobe remains inactive for fifteen clock periods of the CLKIN signal, the Power Down (PDN) signal becomes active, and the PSD will enter into Power Down Mode, discussed next.
55
PSD4000 Series
Preliminary Information 9.5.1 Automatic Power Down (APD) Unit and Power Down Mode (cont.) Power Down Mode By default, if you enable the PSD APD unit, Power Down Mode is automatically enabled. The device will enter Power Down Mode if the address strobe (ALE/AS) remains inactive for fifteen CLKIN (pin PD1) clock periods. The following should be kept in mind when the PSD is in Power Down Mode:
The PSD4000 Functional Blocks
(cont.)
* If the address strobe starts pulsing again, the PSD will return to normal operation. * *
The PSD will also return to normal operation if either the CSI input returns low or the Reset input returns high. The MCU address/data bus is blocked from all memories and PLDs. Various signals can be blocked (prior to Power Down Mode) from entering the PLDs by setting the appropriate bits in the PMMR registers. The blocked signals include MCU control signals and the common clock (CLKIN). Note that blocking CLKIN from the PLDs will not block CLKIN from the APD unit. All PSD memories enter Standby Mode and are drawing standby current. However, the PLDs and I/O ports do not go into Standby Mode because you don't want to have to wait for the logic and I/O to "wake-up" before their outputs can change. See Table 24 for Power Down Mode effects on PSD ports. Typical standby current is 50 A for 5 V parts. This standby current value assumes that there are no transitions on any PLD input.
*
*
Table 24. Power Down Mode's Effect on Ports Port Function
MCU I/O PLD Out Address Out Data Port Peripheral I/O
Pin Level
No Change No Change Undefined Three-State Three-State
Table 25. PSD4000 Timing and Standby Current During Power Down Mode
PLD Propagation Delay
Normal tpd (Note 1)
Mode
Power Down
Memory Access Time
No Access
Access Recovery Time to Normal Access
tLVDV
5V VCC, Typical Standby Current
50 A (Note 2)
NOTES: 1. Power Down does not affect the operation of the PLD. The PLD operation in this mode is based only on the Turbo Bit. 2. Typical current consumption assuming no PLD inputs are changing state and the PLD Turbo bit is off.
56
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Figure 24. APD Logic Block
APD EN PMMR0 BIT 1=1 TRANSITION DETECTION ALE CLR PD SECONDARY FLASH SELECT MAIN FLASH SELECT PLD SRAM SELECT POWER DOWN (PDN) SELECT DISABLE BUS INTERFACE
RESET CSI CLKIN DISABLE MAIN AND SECONDARY FLASH/SRAM EDGE DETECT
APD COUNTER PD
Figure 25. Enable Power Down Flow Chart
RESET
Enable APD Set PMMR0 Bit 1 = 1
OPTIONAL
Disable desired inputs to PLD by setting PMMR0 bit 4 and PMMR2 bits 0.
No
ALE/AS idle for 15 CLKIN clocks? Yes PSD in Power Down Mode
57
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
Table 26. Power Management Mode Registers (PMMR0, PMMR2)**
PMMR0 Bit 7 Bit 6 Bit 5 Bit 4 PLD Array clk 1 = off Bit 3 PLD Turbo 1 = off Bit 2 Bit 1 APD Enable 1 = on Bit 0
*
*
*
*
*
***Bits 0, 2, 6, and 7 are not used, and should be set to 0, bit 5 should be set to 1. ***The PMMR0, and PMMR2 register bits are cleared to zero following power up. ***Subsequent reset pulses will not clear the registers. Bit 1 0 1 Bit 3 0 1 Bit 4 0 Automatic Power Down (APD) is disabled. Automatic Power Down (APD) is enabled. PLD Turbo is on. PLD Turbo is off, saving power. CLKIN input to the PLD AND array is connected. Every CLKIN change will power up the PLD when Turbo bit is off. 1 = CLKIN input to PLD AND array is disconnected, saving power. = = = = =
PMMR2 Bit 7 * Bit 6
PLD array WRH/DBE 1 = off
Bit 5
PLD array ALE 1 = off
Bit 4
PLD** array CNTL2 1 = off
Bit 3
PLD** array CNTL1 1 = off
Bit 2
PLD** array CNTL0 1 = off
Bit 1 *
Bit 0
PLD array Addr. 1 = off
**Unused bits should be set to 0. **Refer to Table 14 the signals that are blocked on pins CNTL0-2. Bit 0 0 = Address A[7:0] inputs to the PLD AND array are connected. 1 = Address A[7:0] inputs to the PLD AND array are disconnected, saving power. Note: In 80C51XA mode, A[7:1] comes from Port F (PF1-PF3) and AD10 [3:0]. Bit 2 0 = Cntl0 input to the PLD AND array is connected. 1 = Cntl0 input to PLD AND array is disconnected, saving power. Bit 3 0 = Cntl1 input to the PLD AND array is connected. 1 = Cntl1 input to PLD AND array is disconnected, saving power. Bit 4 0 = Cntl2 input to the PLD AND array is connected. 1 = Cntl2 input to PLD AND array is disconnected, saving power. Bit 5 0 = ALE input to the PLD AND array is connected. 1 = ALE input to PLD AND array is disconnected, saving power. Bit 6 0 = WRH/DBE input to the PLD AND array is connected. 1 = WRH/DBE input to PLD AND array is disconnected, saving power.
58
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Table 27. APD Counter Operation APD Enable Bit
0 1 1 1
ALE PD Polarity
X X 1 0
ALE Level
X Pulsing 1 0
APD Counter
Not Counting Not Counting Counting (Generates PDN after 15 Clocks) Counting (Generates PDN after 15 Clocks)
9.5.2 Other Power Saving Options
The PSD4000 offers other reduced power saving options that are independent of the Power Down Mode. Except for the SRAM Standby and CSI input features, they are enabled by setting bits in the PMMR0 and PMMR2 registers. 9.5.2.1 Zero Power PLD The power and speed of the PLDs are controlled by the Turbo bit (bit 3) in the PMMR0. By setting the bit to "1", the Turbo mode is disabled and the PLDs consume Zero Power current when the inputs are not switching for an extended time of 70 ns. The propagation delay time will be increased after the Turbo bit is set to "1" (turned off) when the inputs change at a composite frequency of less than 15 MHz. When the Turbo bit is set to a "0" (turned on), the PLDs run at full power and speed. The Turbo bit affects the PLD's D.C. power, AC power, and propagation delay. Refer to AC/DC spec for PLD timings. Note: Blocking MCU control signals with PMMR2 bits can further reduce PLD AC power consumption. 9.5.2.2 SRAM Standby Mode (Battery Backup) The PSD4000 supports a battery backup operation that retains the contents of the SRAM in the event of a power loss. The SRAM has a Vstby pin (PE6) that can be connected to an external battery. When VCC becomes lower than Vstby then the PSD will automatically connect to Vstby as a power source to the SRAM. The SRAM Standby Current (Istby) is typically 0.5 A. The SRAM data retention voltage is 2 V minimum. The battery-on indicator (Vbaton) can be routed to PE7. This signal indicates when the VCC has dropped below the Vstby voltage and that the SRAM is running on battery power. 9.5.2.3 The CSI Input Pin PD2 of Port D can be configured in PSDsoft as the CSI input. When low, the signal selects and enables the internal Flash, Boot Block, SRAM, and I/O for read or write operations involving the PSD4000. A high on the CSI pin will disable the Flash memory, Boot Block, and SRAM, and reduce the PSD power consumption. However, the PLD and I/O pins remain operational when CSI is high. Note: there may be a timing penalty when using the CSI pin depending on the speed grade of the PSD that you are using. See the timing parameter t SLQV in the AC/DC specs. 9.5.2.4 Input Clock The PSD4000 provides the option to turn off the CLKIN input to the PLD AND array to save AC power consumption. During Power Down Mode, or, if the CLKIN input is not being used as part of the PLD logic equation, the clock should be disabled to save AC power. The CLKIN will be disconnected from the PLD AND array by setting bit 4 to a "1" in PMMR0. 9.5.2.5 MCU Control Signals The PSD4000 provides the option to turn off the address input (A7-0) and input control signals (CNTL0-2, ALE, and WRH/DBE) to the PLD to save AC power consumption. These signals are inputs to the PLD AND array. During Power Down Mode, or, if any of them are not being used as part of the PLD logic equation, these control signals should be disabled to save AC power. They will be disconnected from the PLD AND array by setting bits 0, 2, 3, 4, 5, and 6 to a "1" in the PMMR2.
59
PSD4000 Series
Preliminary Information
The PSD4000 Functional Blocks
(cont.)
9.5.3 Reset and Power On Requirement
9.5.3.1 Power On Reset Upon power up the PSD4000 requires a reset pulse of tNLNH-PO (minimum 1 ms) after VCC is steady. During this time period the device loads internal configurations, clears some of the registers and sets the Flash into operating mode. After the rising edge of reset, the PSD4000 remains in the reset state for an additional tOPR (maximum 120 ns) nanoseconds before the first memory access is allowed. The PSD4000 Flash memory is reset to the read array mode upon power up. The FSi and CSBOOTi select signals along with the write strobe signal must be in the false state during power-up reset for maximum security of the data contents and to remove the possibility of data being written on the first edge of a write strobe signal. Any Flash memory write cycle initiation is prevented automatically when VCC is below VLKO. 9.5.3.2 Warm Reset Once the device is up and running, the device can be reset with a much shorter pulse of tNLNH (minimum 150 ns). The same tOPR time is needed before the device is operational after warm reset. Figure 26 shows the timing of the power on and warm reset.
Figure 26. Power On and Warm Reset Timing
OPERATING LEVEL t NLNH-PO VCC t NLNH t NLNH-A
RESET t OPR POWER ON RESET WARM RESET t OPR
9.5.3.3 I/O Pin, Register and PLD Status at Reset Table 28 shows the I/O pin, register and PLD status during power on reset, warm reset and power down mode. PLD outputs are always valid during warm reset, and they are valid in power on reset once the internal PSD configuration bits are loaded. This loading of PSD is completed typically long before the VCC ramps up to operating level. Once the PLD is active, the state of the outputs are determined by the equations specified in PSDsoft.
60
Preliminary Information
PSD4000 Series
The PSD4000 Functional Blocks
(cont.)
Table 28. Status During Power On Reset, Warm Reset and Power Down Mode Port Configuration
MCU I/O PLD Output
Power On Reset
Input Mode Valid after internal PSD configuration bits are loaded Tri-stated Tri-stated
Warm Reset
Input Mode Valid
Power Down Mode
Unchanged Depend on inputs to PLD (address are blocked in PD mode) Not defined Tri-stated
Address Out Data Port
Tri-stated Tri-stated
Register
PMMR0, 2 VM Register*
Power On Reset
Cleared to "0" Initialized based on the selection in PSDsoft Configuration Menu. Cleared to "0"
Warm Reset
Unchanged
Power Down Mode
Unchanged
Initialized based on Unchanged the selection in PSDsoft Configuration Menu. Cleared to "0" Unchanged
All other registers
*SR_cod bit in the VM Register are always cleared to zero on power on or warm reset. 9.5.3.4 Reset of Flash Erase and Programming Cycles An external reset on the RESET pin will also reset the internal Flash memory state machine. When the Flash is in programming or erase mode, the RESET pin will terminate the programming or erase operation and return the Flash back to read mode in tNLNH-A (minimum 25 s) time.
9.6 Programming In-Circuit using the JTAG-ISP Interface
The JTAG-ISP interface on the PSD4000 can be enabled on Port E (see Table 29). All memory (Flash and Flash Boot Block), PLD logic, and PSD configuration bits may be programmed through the JTAG-ISC interface. A blank part can be mounted on a printed circuit board and programmed using JTAG-ISP. The standard JTAG signals (IEEE 1149.1) are TMS, TCK, TDI, and TDO. Two additional signals, TSTAT and TERR, are optional JTAG extensions used to speed up program and erase operations. By default, on a blank PSD (as shipped from factory or after erasure), four pins on Port E are enabled for the basic JTAG signals TMS, TCK, TDI, and TDO. See Application Note 54 for more details on JTAG In-System-Programming.
Table 29. JTAG Port Signals Port E Pin
PE0 PE1 PE2 PE3 PE4 PE5
JTAG Signals
TMS TCK TDI TDO TSTAT TERR
Description
Mode Select Clock Serial Data In Serial Data Out Status Error Flag
61
PSD4000 Series
Preliminary Information 9.6.1 Standard JTAG Signals The JTAG configuration bit (non-volatile) inside the PSD can be set by the user in the PSDsoft. Once this bit is set and programmed in the PSD, the JTAG pins are dedicated to JTAG at all times and is in compliance with IEEE 1149.1. After power up the standard JTAG signals (TDI, TDO TCK and TMS) are inputs, waiting for a serial command from an external JTAG controller device (such as FlashLink or Automated Test Equipment). When the enabling command is received from the external JTAG controller, TDO becomes an output and the JTAG channel is fully functional inside the PSD. The same command that enables the JTAG channel may optionally enable the two additional JTAG pins, TSTAT and TERR. The PSD4000 supports JTAG ISP commands, but not Boundary Scan. ST's PSDsoft software tool and FlashLink JTAG programming cable implement these JTAG-ISP commands. 9.6.2 JTAG Extensions TSTAT and TERR are two JTAG extension signals enabled by a JTAG command received over the four standard JTAG pins (TMS, TCK, TDI, and TDO). They are used to speed programming and erase functions by indicating status on PSD pins instead of having to scan the status out serially using the standard JTAG channel. See Application Note 54. TERR will indicate if an error has occurred when erasing a sector or programming a byte in Flash memory. This signal will go low (active) when an error condition occurs, and stay low until a special JTAG command is executed or a chip reset pulse is received after an "ISC-DISABLE" command. TSTAT behaves the same as the Rdy/Bsy signal described in section 9.1.1.2. TSTAT will be high when the PSD4000 device is in read array mode (Flash memory and Boot Block contents can be read). TSTAT will be low when Flash memory programming or erase cycles are in progress, and also when data is being written to the Secondary Flash Block. TSTAT and TERR can be configured as open-drain type signals with a JTAG command. 9.6.3 Security and Flash Memories Protection When the security bit is set, the device cannot be read on a device programmer or through the JTAG Port. When using the JTAG Port, only a full chip erase command is allowed. All other program/erase/verify commands are blocked. Full chip erase returns the part to a non-secured blank state. The Security Bit can be set in PSDsoft. All Flash Memory and Boot sectors can individually be sector protected against erasures. The sector protect bits can be set in PSDsoft.
The PSD4000 Functional Blocks
(cont.)
62
Preliminary Information
PSD4000 Series
10.0 Absolute Maximum Ratings
Symbol
TSTG
Parameter
Storage Temperature Operating Temperature Voltage on any Pin
Condition
PLDCC Commercial Industrial With Respect to GND With Respect to GND With Respect to GND
Min
- 65 0 - 40 - 0.6 - 0.6 - 0.6
Max
+ 125 + 70 + 85 +7 + 14 +7
Unit
C C C V V V V
VPP VCC
Device Programmer Supply Voltage Supply Voltage ESD Protection
>2000
NOTE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not recommended. Exposure to Absolute Maximum Rating conditions for extended periods of time may affect device reliability.
11.0 Operating Range
Range
Commercial Industrial Commercial Industrial
Temperature
0 C to +70C -40 C to +85C 0 C to +70C -40 C to +85C
VCC Tolerance
+ 5 V 10% + 5 V 10% 3.0 V to 3.6 V 3.0 V to 3.6 V
12.0 Recommended Operating Conditions
Symbol
VCC VCC
Parameter
Supply Voltage Supply Voltage
Condition
All Speeds V-Versions All Speeds
Min
4.5 3.0
Typ
5
Max
5.5 3.6
Unit
V V
63
PSD4000 Series
Preliminary Information The following tables describe the AD/DC parameters of the PSD4000 family:
AC/DC Parameters
t DC Electrical Specification t AC Timing Specification
* PLD Timing *
- Combinatorial Timing Microcontroller Timing - Read Timing - Write Timing - Power Down and Reset Timing
Following are issues concerning the parameters presented:
t In the DC specification the supply current is given for different modes of operation.
Before calculating the total power consumption, determine the percentage of time that the PSD4000 is in each mode. Also, the supply power is considerably different if the Turbo bit is "OFF".
t The AC power component gives the PLD, Flash memory, and SRAM mA/MHz
specification. Figures 27 and 27a show the PLD mA/MHz as a function of the number of Product Terms (PT) used.
t In the PLD timing parameters, add the required delay when Turbo bit is "OFF". Figure 27. PLD ICC /FrequencyConsumption (VCC = 5 V 10%)
110 100 90 80 ICC - (mA) 70
FF O
VCC = 5V
TU RB O O
10 N(
0%
)
60 50 40 30 20 10 0 0 5
TU RB
ON BO TUR
(25%
)
O
T
UR
BO
OF
F
PT 100% PT 25%
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
64
Preliminary Information
PSD4000 Series
AC/DC Parameters
(cont.)
Figure 27a. PLD ICC /Frequency Consumption (PSD4135G2V Versions, VCC = 3 V)
60 VCC = 3V 50 ICC - (mA) 40
TU
ON ( RBO
100%
)
O FF
30 20 10 0 0
TU RB O
T
ON (2 URBO
5%)
R TU
BO
O
FF
PT 100% PT 25%
5
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
Example of PSD4000 Typical Power Calculation at VCC = 5.0 V Conditions
Highest Composite PLD input frequency (Freq PLD) MCU ALE frequency (Freq ALE) % Flash Access % SRAM access % I/O access Operational Modes % Normal % Power Down Mode Number of product terms used (from fitter report) % of total product terms Turbo Mode = = = = = = = = = = 8 MHz 4 MHz 80% 15% 5% (no additional power above base) 10% 90% 45 PT 45/176 = 25.5% ON
Calculation (typical numbers used)
ICC total = Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc)) = Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE + %SRAM x 1.5 mA/MHz x Freq ALE + % PLD x 2 mA/MHz x Freq PLD + #PT x 400 A/PT = 50 A x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz + 0.15 x 1.5 mA/MHz x 4 MHz +2 mA/MHz x 8 MHz + 45 x 0.4 mA/PT) = 45 A + 0.1 x (8 + 0.9 + 16 + 18 mA) = 45 A + 0.1 x 42.9 = 45 A + 4.29 mA = 4.34 mA This is the operating power with no Flash writes or erases. Calculation is based on IOUT = 0 mA. 65
PSD4000 Series
Preliminary Information
AC/DC Parameters
(cont.)
Example of Typical Power Calculation at VCC = 5.0 V in Turbo Off Mode Conditions
Highest Composite PLD input frequency (Freq PLD) = MCU ALE frequency (Freq ALE) % Flash Access % SRAM access % I/O access Operational Modes % Normal % Power Down Mode Number of product terms used (from fitter report) % of total product terms Turbo Mode = = = = = = = = = 8 MHz 4 MHz 80% 15% 5% (no additional power above base) 10% 90% 45 PT 45/176 = 25.5% Off
Calculation (typical numbers used)
ICC total = Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc)) = Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE + %SRAM x 1.5 mA/MHz x Freq ALE + % PLD x (from graph using Freq PLD)) = 50 A x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz + 0.15 x 1.5 mA/MHz x 4 MHz + 24 mA) = 45 A + 0.1 x (8 + 0.9 + 24) = 45 A + 0.1 x 32.9 = 45 A + 3.29 mA = 3.34 mA This is the operating power with no Flash writes or erases. Calculation is based on IOUT = 0 mA.
66
Preliminary Information
PSD4000 Series (5 V 10% Versions)
PSD4000 DC Characteristics
Symbol
VCC VIH VIL VIH1 VIL1 VHYS VLKO VOL
Parameter
Supply Voltage High Level Input Voltage Low Level Input Voltage Reset High Level Input Voltage Reset Low Level Input Voltage Reset Pin Hysteresis VCC Min for Flash Erase and Program Output Low Voltage
Conditions
All Speeds 4.5 V < VCC < 5.5 V 4.5 V < VCC < 5.5 V (Note 1) (Note 1)
Min
4.5 2 -.5 .8 VCC -.5 0.3 2.5
Typ
5
Max
5.5 VCC +.5 0.8 VCC +.5 .2 VCC -.1 4.2
Unit
V V V V V V V V V V V V
IOL = 20 A, VCC = 4.5 V IOL = 8 mA, VCC = 4.5 V
0.01 0.25 4.4 2.4 VSBY - 0.8 2.0 4.49 3.9
0.1 0.45
VOH VOH1 VSBY ISBY IIDLE VDF ISB ILI ILO IO
Output High Voltage Except VSTBY On Output High Voltage VSTBY On SRAM Standby Voltage SRAM Standby Current (VSTBY Pin) Idle Current (VSTBY Pin) SRAM Data Retention Voltage Standby Supply Current for Power Down Mode Input Leakage Current Output Leakage Current Output Current
IOH = -20 A, VCC = 4.5 V IOH = -2 mA, VCC = 4.5 V IOH1 = -1 A VCC = 0 V VCC > VSBY Only on VSTBY CSI > VCC -0.3 V (Notes 2, 3 and 5) VSS < VIN < VCC 0.45 < VIN < VCC Refer to IOL and IOH in the VOL and VOH row PLD_TURBO = OFF, f = 0 MHz (Note 3)
VCC 0.5 1 0.1
V A A V
-0.1 2 100 -1 -10 .1 5
200 1 10
A A A
0 400 15 0 0 Fig. 27 (Note 4) 2.5 1.5 3.5 3.0 700 30 0 0
mA A/PT mA mA mA
PLD Only ICC (DC) (Note 5) Operating Supply Current Flash
PLD_TURBO = ON, f = 0 MHz During Flash Write/Erase Only Read Only, f = 0 MHz
SRAM PLD AC Base ICC (AC) (Note 5) FLASH AC Adder SRAM AC Adder
NOTE: 1. 2. 3. 4. 5.
f = 0 MHz
mA/MHz mA/MHz
Reset input has hysteresis. VIL1 is valid at or below .2VCC -.1. VIH1 is valid at or above .8VCC. CSI deselected or internal Power Down mode is active. PLD is in non-turbo mode and none of the inputs are switching Refer to Figure 32 for PLD current calculation. I O = 0 mA
67
PSD4000 Series
Preliminary Information
Microcontroller Interface - AC/DC Parameters
(5V 10% Versions)
AC Symbols for PLD Timing. Example:
A C D E I L N P R S T W B M - - - - - - - - - - - - - - t AVLX - Time from Address Valid to ALE Invalid.
Signal Letters
Address Input CEout Output Input Data E Input Interrupt Input ALE Input Reset Input or Output Port Signal Output UDS, LDS, DS, RD, PSEN Inputs Chip Select Input R/W Input WR Input Vstby Output Output MicroCell
Signal Behavior
t L H V X Z PW - - - - - - - Time Logic Level Low or ALE Logic Level High Valid No Longer a Valid Logic Level Float Pulse Width
68
Preliminary Information
PSD4000 Series
Microcontroller Interface - PSD4000 AC/DC Parameters
(5V 10% Versions)
Read Timing (5 V 10% Versions)
-70
Symbol
t LVLX t AVLX t LXAX t AVQV t SLQV t RLQV t RHQX t RLRH t RHQZ t EHEL t THEH t ELTL t AVPV
NOTES: 1. 2. 3. 4. 5.
-90
Min
20 6 8 70 75 24 31 90 100 32 38 0 32 20 25 32 10 0 20 25
Parameter
ALE or AS Pulse Width Address Setup Time Address Hold Time Address Valid to Data Valid CS Valid to Data Valid RD to Data Valid RD or PSEN to Data Valid, 80C51XA Mode RD Data Hold Time RD Pulse Width RD to Data High-Z E Pulse Width R/W Setup Time to Enable R/W Hold Time After Enable Address Input Valid to Address Output Delay
Conditions
(Note 3) (Note 3) (Note 3) (Note 5) (Note 2) (Note 1) (Note 1) (Note 1)
Min
15 4 7
Max
Max
Turbo Off
Unit
ns ns ns
Add 12**
ns ns ns ns ns ns ns ns ns ns ns
0 27 27 6 0
(Note 4)
RD timing has the same timing as DS, LDS, UDS, and PSEN signals. RD and PSEN have the same timing. Any input used to select an internal PSD4000 function. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port. RD timing has the same timing as DS, LDS, and UDS signals.
69
PSD4000 Series
Preliminary Information
Microcontroller Interface - PSD4000 AC/DC Parameters
(5V 10% Versions)
Write Timing (5 V 10% Versions)
-70
Symbol
t LVLX t AVLX t LXAX t AVWL t SLWL t DVWH t WHDX t WLWH t WHAX1 t WHAX2 t WHPV t AVPV
NOTES: 1. 2. 3. 4.
-90
Min
20 6 8 15 15 35 5 35 8 0 27 20 30 25 ns ns ns ns ns ns ns ns ns ns ns
Parameter
ALE or AS Pulse Width Address Setup Time Address Hold Time Address Valid to Leading Edge of WR CS Valid to Leading Edge of WR WR Data Setup Time WR Data Hold Time WR Pulse Width Trailing Edge of WR to Address Invalid Trailing Edge of WR to DPLD Address Input Invalid Trailing Edge of WR to Port Output Valid Using I/O Port Data Register Address Input Valid to Address Output Delay
Conditions
(Note 1) (Note 1) (Notes 1 and 3) (Note 3) (Note 3) (Note 3) (Note 3) (Note 3) (Note 3 and 4) (Note 3) (Note 2)
Min
15 4 7 8 12 25 4 28 6 0
Max
Max
Unit
Any input used to select an internal PSD4000 function. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port. WR timing has the same timing as E, DS, LDS, UDS, WRL, and WRH signals. tWHAX2 is Address Hold Time for DPLD inputs that are used to generate chip selects for internal PSD memory.
PLD Combinatorial Timing (5 V 10%)
-70 -90 TURBO OFF
Add 12
Slew Rate
(Note 1)
Symbol
t PD t ARD
Parameter
PLD Input Pin/Feedback to PLD Combinatorial Output PLD Array Delay
Conditions
Min
Max
20 11
Min
Max
25 16
Unit
ns ns
Sub 2
NOTE: 1. Fast Slew Rate output available on Port C and F.
70
Preliminary Information
PSD4000 Series
Microcontroller Interface - PSD4000 AC/DC Parameters
(5V 10% Versions)
Power Down Timing (5 V 10%)
-70
Symbol
t LVDV
-90
Min Max
90
Parameter
ALE Access Time from Power Down Maximum Delay from APD Enable to Internal PDN Valid Signal
Conditions
Min
Max
80
Unit
ns s
t CLWH
Using CLKIN Input
15 * t CLCL (s) (Note 1)
NOTE: 1. t CLCL is the CLKIN clock period.
Vstbyon Timing (5 V 10%)
Symbol
t BVBH t BXBL
Parameter
Vstby Detection to Vstbyon Output High Vstby Off Detection to Vstbyon Output Low
Conditions
(Note 1) (Note 1)
Min
Typ
20 20
Max
Unit
s s
NOTE: 1. Vstbyon is measured at VCC ramp rate of 2 ms.
Reset Pin Timing (5 V 10%)
Symbol
t NLNH t OPR t NLNH-PO t NLNH-A
Parameter
Warm RESET Active Low Time (Note 1) RESET High to Operational Device Power On Reset Active Low Time Warm RESET Active Low Time (Note 2)
Conditions
Min
150
Typ
Max
Unit
ns
120 1 25
ns ms s
NOTE: 1. RESET will not abort Flash programming/erase cycles. 2. RESET will abort Flash programming or erase cycle.
71
PSD4000 Series
Preliminary Information
Microcontroller Interface - PSD4000 AC/DC Parameters
(5V 10% Versions)
Flash Program, Write and Erase Times (5 V 10%)
Symbol Parameter
Flash Program Flash Bulk Erase (Preprogrammed to 00) (Note 1) Flash Bulk Erase t WHQV3 t WHQV2 t WHQV1 t WHWLO t Q7VQV Sector Erase (Preprogrammed to 00) Sector Erase Word Program Program/Erase Cycles (Per Sector) Sector Erase Time-Out DQ7 Valid to Output Valid (Data Polling) (Notes 2 and 3) 100,000 100 30
Min
Typ
8.5 3 10 1 2.2 14
Max
Unit
sec
30 30 1200
sec sec sec sec s cycles s ns
NOTE: 1. Programmed to all zeros before erase. 2. The polling status DQ7 is valid tQ7VQV ns before the data DQ0-7 is valid for reading. 3. DQ7 is DQ15 for Motorola MCU with 16-bit data bus.
ISC Timing (5 V 10%)
-70
Symbol
t ISCCF t ISCCH t ISCCL t ISCCF-P t ISCCH-P t ISCCL-P t ISCPSU t ISCPH t ISCPCO t ISCPZV t ISCPVZ
-90
Min Max
18 26 26 2 2 240 240 8 5 21 21 21 23 23 23
Parameter
TCK Clock Frequency (except for PLD) TCK Clock High Time TCK Clock Low Time TCK Clock Frequency (for PLD only) TCK Clock High Time (for PLD only) TCK Clock Low Time (for PLD only) ISC Port Set Up Time ISC Port Hold Up Time ISC Port Clock to Output ISC Port High-Impedance to Valid Output ISC Port Valid Output to High-Impedance
Conditions
(Note 1) (Note 1) (Note 1) (Note 2) (Note 2) (Note 2)
Min
Max
20
Unit
MHz ns ns MHz ns ns ns ns ns ns ns
23 23 240 240 6 5
NOTES: 1. For "non-PLD" programming, erase or in ISC by-pass mode. 2. For program or erase PLD only.
72
Preliminary Information
PSD4000 Series (3.0 V to 3.6 V Versions)
PSD4000 DC Characteristics
Symbol
VCC VIH VIL VIH1 VIL1 VHYS VLKO VOL
Advance Information
Min
3.0 .7 VCC -.5 .8 VCC -.5 0.3 1.5 2.3 0.01 0.15 2.9 2.7 VSBY - 0.8 2.0 VCC 0.5 -0.1 2 50 -1 -10 .1 5 100 1 10 1 0.1 2.99 2.8 0.1 0.45
Parameter
Supply Voltage High Level Input Voltage Low Level Input Voltage Reset High Level Input Voltage Reset Low Level Input Voltage Reset Pin Hysteresis VCC Min for Flash Erase and Program Output Low Voltage
Conditions
All Speeds 3.0 V < VCC < 3.6 V 3.0 V < VCC < 3.6 V (Note 1) (Note 1)
Typ
Max
3.6 VCC +.5 0.8 VCC +.5 .2 VCC -.1
Unit
V V V V V V V V V V V V V A A V A A A
IOL = 20 A, VCC = 3.0 V IOL = 4 mA, VCC = 3.0 V
VOH VOH1 VSBY ISBY IIDLE VDF ISB ILI ILO IO
Output High Voltage Except VSTBY On Output High Voltage VSTBY On SRAM Standby Voltage SRAM Standby Current (VSTBY Pin) Idle Current (VSTBY Pin) SRAM Data Retention Voltage Standby Supply Current for Power Down Mode Input Leakage Current Output Leakage Current Output Current
IOH = -20 A, VCC = 3.0 V IOH = -1 mA, VCC = 3.0 V IOH1 = -1 A VCC = 0 V VCC > VSBY Only on VSTBY CSI >VCC -0.3 V (Notes 2 and 3) VSS < VIN < VCC 0.45 < VIN < VCC Refer to IOL and IOH in the VOL and VOH row PLD_TURBO = OFF, f = 0 MHz (Note 3)
0 200 10 0 0 (Note 4) 1.5 0.8 2.0 1.5 400 25 0 0
mA A/PT mA mA mA Figure 27a mA/MHz mA/MHz
PLD Only ICC (DC) (Note 5) Operating Supply Current FLASH
PLD_TURBO = ON, f = 0 MHz During FLASH Write/Erase Only Read Only, f = 0 MHz
SRAM PLD AC Base ICC (AC) (Note 5) FLASH AC Adder SRAM AC Adder
NOTES: 1. 2. 3. 4. 5.
f = 0 MHz
Reset input has hysteresis. VIL1 is valid at or below .2VCC -.1. VIH1 is valid at or above .8VCC. CSI deselected or internal PD mode is active. PLD is in non-turbo mode and none of the inputs are switching. Refer to Figure 31a for PLD current calculation. I O = 0 mA.
73
PSD4000 Series
Preliminary Information
Microcontroller Interface - PSD4000 AC/DC Parameters
(3.0 V to 3.6 V Versions)
AC Symbols for PLD Timing. Example:
A C D E L N P Q R S T W B - - - - - - - - - - - - - t AVLX - Time from Address Valid to ALE Invalid.
Signal Letters
Address Input CEout Output Input Data E Input ALE Input Reset Input or Output Port Signal Output Output Data WR, UDS, LDS, DS, IORD, PSEN Inputs Chip Select Input R/W Input Internal PDN Signal Vstby Output
Signal Behavior
t L H V X Z PW - - - - - - - Time Logic Level Low or ALE Logic Level High Valid No Longer a Valid Logic Level Float Pulse Width
74
Preliminary Information
PSD4000 Series
Microcontroller Interface - PSD4000 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Read Timing (3.0 V to 3.6 V Versions)
-90
Symbol
t LVLX t AVLX t LXAX t AVQV t SLQV t RLQV t RHQX t RLRH t RHQZ t EHEL t THEH t ELTL t AVPV
NOTES: 1. 2. 3. 4. 5.
-12
Min
24 9 10 90 90 35 45
Parameter
ALE or AS Pulse Width Address Setup Time Address Hold Time Address Valid to Data Valid CS Valid to Data Valid RD to Data Valid RD or PSEN to Data Valid, 80C51XA Mode RD Data Hold Time RD Pulse Width RD to Data High-Z E Pulse Width R/W Setup Time to Enable R/W Hold Time After Enable Address Input Valid to Address Output Delay
Conditions
(Note 3) (Note 3) (Note 3) (Note 5) (Note 2) (Note 1) (Note 1) (Note 1)
Min
22 7 8
Max
Max
Turbo Off
Unit
ns ns ns
120 Add 20** 120 35 48 0 40
ns ns ns ns ns ns
0 36 38 38 10 0
40 42 16 0
ns ns ns ns
(Note 4)
30
35
ns
RD timing has the same timing as DS, LDS, UDS, and PSEN signals. RD and PSEN have the same timing for 80C51XA. Any input used to select an internal PSD4135G2V function. In multiplexed mode latched address generated from ADIO delay to address output on any Port. RD timing has the same timing as DS, LDS, and UDS signals.
75
PSD4000 Series
Preliminary Information
Microcontroller Interface - PSD4000 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Write Timing (3.0 V to 3.6 V Versions)
-90
Symbol
t LVLX t AVLX t LXAX t AVWL t SLWL t DVWH t WHDX t WLWH t WHAX1 t WHAX2 t WHPV t AVPV
NOTES: 1. 2. 3. 4.
-12
Min
24 9 10 18 18 45 8 45 10 0 33 30 33 35 ns ns ns ns ns ns ns ns ns ns ns
Parameter
ALE or AS Pulse Width Address Setup Time Address Hold Time Address Valid to Leading Edge of WR CS Valid to Leading Edge of WR WR Data Setup Time WR Data Hold Time WR Pulse Width Trailing Edge of WR to Address Invalid Trailing Edge of WR to DPLD Address Input Invalid Trailing Edge of WR to Port Output Valid Using I/O Port Data Register Address Input Valid to Address Output Delay
Conditions
(Note 1) (Note 1) (Notes 1 and 3) (Note 3) (Note 3) (Note 3) (Note 3) (Note 3) (Notes 3 and 4) (Note 3) (Note 2)
Min
22 7 8 15 15 40 5 40 8 0
Max
Max
Unit
Any input used to select an internal PSD4000 function. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port. WR timing has the same timing as E, DS, LDS, UDS, WRL, and WRH signals. tWHAX2 is Address hold time for DPLD inputs that are used to generate chip selects for internal PSD memory.
PLD Combinatorial Timing (3.0 V to 3.6 V Versions)
-90 -12 TURBO OFF
Add 20
Slew Rate
(Note 1)
Symbol
t PD t ARD
Parameter
PLD Input Pin/Feedback to PLD Combinatorial Output PLD Array Delay
Conditions
Min
Max
38 23
Min
Max
43 27
Unit
ns ns
Sub 6
NOTE: 1. Fast Slew Rate output available on Port C and F.
76
Preliminary Information
PSD4000 Series
Microcontroller Interface - PSD4000 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Power Down Timing (3.0 V to 3.6 V Versions)
-90
Symbol
t LVDV t CLWH
-12
Min Max
135
Parameter
ALE Access Time from Power Down Maximum Delay from APD Enable to Internal PDN Valid Signal
Conditions
Min
Max
128
Unit
ns s
Using CLKIN Input
15 * t CLCL (s) (Note 1)
NOTE: 1. tCLCL is the CLKIN clock period.
Vstbyon Timing (3.0 V to 3.6 V Versions)
Symbol
t BVBH t BXBL
Parameter
Vstby Detection to Vstbyon Output High Vstby Off Detection to Vstbyon Output Low
Conditions
(Note 1) (Note 1)
Min
Typ
20 20
Max
Unit
s s
NOTE: 1. Vstbyon is measured at VCC ramp rate of 2 ms.
Reset Pin Timing (3.0 V to 3.6 V Versions)
Symbol
t NLNH t OPR t NLNH-PO t NLNH-A
Parameter
Warm RESET Active Low Time (Note 1) RESET High to Operational Device Power On Reset Active Low Time Warm RESETActive Low Time (Note 2)
Conditions
Min
300
Typ
Max
Unit
ns
300 1 25
ns ms s
NOTE: 1. RESET will not abort Flash programming/erase cycles. 2. RESET will abort Flash programming or erase cycle.
77
PSD4000 Series
Preliminary Information
Microcontroller Interface - PSD4000 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Flash Program, Write and Erase Times (3.0 V to 3.6 V Versions)
Symbol Parameter
Flash Program Flash Bulk Erase (Preprogrammed to 00) (Note 1) Flash Bulk Erase t WHQV3 t WHQV2 t WHQV1 t WHWLO t Q7VQV Sector Erase (Preprogrammed to 00) Sector Erase Word Program Program/Erase Cycles (Per Sector) Sector Erase Time-Out DQ7 Valid to Output Valid (Data Polling) (Notes 2 and 3) 100,000 100 30
Min
Typ
8.5 3 10 1 2.2 14
Max
Unit
sec
30 30 1200
sec sec sec sec s cycles s ns
NOTES: 1. Programmed to all zeros before erase. 2. The polling status DQ7 is valid tQ7VQV ns before the data DQ0-7 is valid for reading. 3. DQ7 is DQ15 for Motorola MCU with 16-bit data bus.
ISC Timing (3.0 V to 3.6 V Versions)
-90
Symbol
t ISCCF t ISCCH t ISCCL t ISCCF-P t ISCCH-P t ISCCL-P t ISCPSU t ISCPH t ISCPCO t ISCPZV t ISCPVZ
-12
Min Max
12 40 40 2 2 240 240 12 5 26 26 26 32 32 32
Parameter
TCK Clock Frequency (except for PLD) TCK Clock High Time TCK Clock Low Time TCK Clock Frequency (for PLD only) TCK Clock High Time (for PLD only) TCK Clock Low Time (for PLD only) ISC Port Set Up Time ISC Port Hold Up Time ISC Port Clock to Output ISC Port High-Impedance to Valid Output ISC Port Valid Output to High-Impedance
Conditions
(Note 1) (Note 1) (Note 1) (Note 2) (Note 2) (Note 2)
Min
Max
15
Unit
MHz ns ns MHz ns ns ns ns ns ns ns
30 30 240 240 11 5
NOTES: 1. For "non-PLD" programming, erase or in ISC by-pass mode. 2. For program or erase PLD only.
78
Preliminary Information
PSD4000 Series
Figure 28. Read Timing
tAVLX ALE/AS tLVLX A/D MULTIPLEXED BUS ADDRESS NON-MULTIPLEXED BUS DATA NON-MULTIPLEXED BUS
tLXAX*
ADDRESS VALID tAVQV ADDRESS VALID
DATA VALID
DATA VALID tSLQV
CSI tRLQV tRLRH RD (PSEN, DS) tRHQZ tRHQX
tEHEL E tTHEH tELTL
R/W
tAVPV ADDRESS OUT
*tAVLX and tLXAX are not required 80C51XA in Burst Mode.
79
PSD4000 Series
Preliminary Information
Figure 29. Write Timing
tAVLX ALE/AS
t LXAX
t LVLX A/D MULTIPLEXED BUS ADDRESS VALID tAVWL ADDRESS NON-MULTIPLEXED BUS DATA NON-MULTIPLEXED BUS tSLWL CSI tDVWH WR (DS) t WLWH t WHDX t WHAX ADDRESS VALID DATA VALID DATA VALID
t EHEL E t THEH R/ W t WLMV tAVPV ADDRESS OUT t WHPV STANDARD MCU I/O OUT t ELTL
80
Preliminary Information
PSD4000 Series
Figure 30. Combinatorial Timing - PLD
GPLD INPUT t PD GPLD OUTPUT
Figure 31. JTAG-ISP Timing
t ISCCH
TCK
t ISCCL t ISCPSU t ISCPH
TDI/TMS
t ISCPZV t ISCPCO
ISC OUTPUTS/TDO
t ISCPVZ
ISC OUTPUTS/TDO
81
PSD4000 Series
Preliminary Information
Figure 32. Reset Timing
OPERATING LEVEL t NLNH- PO VCC t NLNH t NLNH-A
RESET t OPR POWER ON RESET WARM RESET t OPR
Figure 33. Key to Switching Waveforms
WAVEFORMS
INPUTS
OUTPUTS
STEADY INPUT
STEADY OUTPUT
MAY CHANGE FROM HI TO LO MAY CHANGE FROM LO TO HI
WILL BE CHANGING FROM HI TO LO WILL BE CHANGING LO TO HI
DON'T CARE
CHANGING, STATE UNKNOWN
OUTPUTS ONLY
CENTER LINE IS TRI-STATE
82
Preliminary Information
PSD4000 Series
14.0 Pin Capacitance
TA = 25 C, f = 1 MHz
Symbol
CIN COUT CVPP
Parameter 1
Capacitance (for input pins only) Capacitance (for input/output pins) Capacitance (for CNTL2/VPP)
Conditions Typical 2 Max Unit
VIN = 0 V VOUT = 0 V VPP = 0 V 4 8 18 6 12 25 pF pF pF
NOTES: 1. These parameters are only sampled and are not 100% tested. 2. Typical values are for TA = 25C and nominal supply voltages.
15.0 Figure 34. AC Testing Input/Output Waveform
3.0V TEST POINT 0V 1.5V
16.0 Figure 35. AC Testing Load Circuit
DEVICE UNDER TEST
2.01 V
195
CL = 30 pF (INCLUDING SCOPE AND JIG CAPACITANCE)
17.0 Programming
Upon delivery from ST, the PSD4000 device has all bits in the PLDs and memories in the "1" or high state. The configuration bits are in the "0" or low state. The code, configuration, and PLDs logic are loaded through the procedure of programming. Information for programming the device is available directly from ST. Please contact your local sales representative. (See the last page.)
83
PSD4000 Series
Preliminary Information
18.0 PSD4000 Pin Assignments
80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U) Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Pin Assignments
PD2 PD3 AD0 AD1 AD2 AD3 AD4 GND VCC AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 VCC GND PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 RESET CNTL2
Pin No.
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Assignments
PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 GND GND PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 CNTL0 CNTL1 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 VCC GND PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 PD0 PD1
84
Preliminary Information
PSD4000 Series
70 GND
69 VCC 68 PB7
67 PB6
66 PB5
65 PB4
64 PB3
63 PB2
62 PB1
PD2 PD3 AD0 AD1 AD2 AD3 AD4 VCC AD5 AD6 AD7 AD8 AD9
1 2 3 4 5 6 7 9 10 11 12 13 14
61 PB0
80 PD1
79 PD0
78 PE7
77 PE6
76 PE5
75 PE4
74 PE3
73 PE2
72 PE1
71 PE0
19.0 PSD4000 Package Information
Figure 36. Drawing U5 - 80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U)
60 CNTL1 59 CNTL0 58 PA7 57 PA6 56 PA5 55 PA4 54 PA3 53 PA2 52 PA1 51 PA0 50 GND 49 GND 48 PC7 47 PC6 46 PC5 45 PC4 44 PC3 43 PC2 42 PC1 41 PC0
GND 8
AD10 15 AD11 16 AD12 17 AD13 18 AD14 19 AD15 20
PG0 21
PG1 22
PG2 23
PG3 24
PG4 25
PG5 26
PG6 27
PG7 28
VCC 29
GND 30
PF0 31
PF1 32
PF2 33
PF3 34
PF4 35
PF5 36
PF6 37
PF7 38
RESET 39
CNTL2 40
85
PSD4000 Series
Preliminary Information
Figure 36A. Drawing U5 - 80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U)
D D1 D3
80 1 2 3
Index Mark
E3
E1
E
Standoff: 0.05 mm Min. A1 A2 A
C
L B e1 Load Coplanarity: 0.102 mm Max.
Family: Plastic Thin Quad Flatpack (TQFP)
Millimeters Symbol
A A2 B C D D1 D3 E E1 E3 e1 L N 0.45 80 13.95 11.95 9.5 0.50 0.75 13.95 11.95 9.5 14.05 12.05 Reference Reference 0.018 80
060198R0
Inches Notes Min
0 - 0.037 Reference 0.007 0.512 0.433 Reference 0.512 0.433 0.374 0.019 0.030 0.374 0.551 0.472 Reference Reference
Min
0 - 0.95 0.17
Max
7 1.20 1.05 0.27 0.20 14.05 12.05
Max
8 0.047 0.041 0.011 0.008 0.551 0.472
Notes
Reference
86
Preliminary Information
20.0 Selector Guide
Selector Guide - PSD4000 Series
Part #
5 Volts
MCU
Data Path
PLDs/Decoders
Inputs Input Macrocells Output Macrocells Outputs Page Reg.
I/O
Memory
Other
Software
PSDsoft Express PSDsoft 2000
Ports Flash Program Store ISP via JTAG 2nd Flash Array IAP via MCU EEPROM Zero Power SRAM Per. Mode w/BB Security PMU APD
PSD4135G2 PSD4235G2
16 16
57 57
- 24
- 16
24 24
8-bit 8-bit
52 52
4096Kb 256Kb 4096Kb 256Kb
- -
64Kb 64Kb
X X
X X
X X
- -
X X
X X
X X
X X
X
PSD4000 Series
87
PSD4000 Series
Preliminary Information
Flash PSD Part Number Construction
CHARACTER # 1 PART NUMBER I P 2 I S 3 I D 4 I 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 I I I I I I I I I I I I I I 42 1 3F2 -A-1 5J
21.0 Part Number Construction
PSD BRAND NAME PSD = Standard Low Power Device FAMILY/SERIES 8 = Flash PSD for 8-bit MCUs 9 = Flash PSD for 8-bit MUCs (with simple PLD) 41 = Flash PSD for 16-bit MUCs (with simple PLD) 42 = Flash PSD for 16-bit MUCs (with CPLD) SRAM SIZE 0 = 0Kb 1 = 16Kb 2 = 32Kb 3 = 64Kb NVM SIZE 1 = 256Kb 2 = 512Kb 3 = 1Mb 4 = 2Mb 5 = 4Mb
TEMP RANGE "Blank" = 0C to +70C (Commercial) I = -40C to +85C (Industrial)
PACKAGE TYPE J = PLCC U = TQFP M = PQFP B81 = BGA
SPEED - 70 = 70ns - 90 = 90ns - 12 = 120ns - 15 = 150ns - 20 = 200ns
REVISION "Blank" = no rev. - A = Rev. A - B = Rev. B - C = Rev. C
Vc c VOLTAGE I/O COUNT & OTHER F = 27 I/O G = 52 I/O 2ND NVM TYPE, SIZE & CONFIGURATION 1 = EEPROM, 256Kb 2 = FLASH, 256Kb 3 = No 2nd Array "blank" = 5 Volt V = 3.0 Volt
22.0 Ordering Information
88
PSD4135G2
REVISION HISTORY Table 1. Document Revision History
Date 01-May-2000 Rev. 1.0 Description of Revision PSD4135G2: Document written in the WSI format. Initial release PSD4135G2: Flash In-System-Programmable Peripherals for 16-Bit MCUs Front page, and back two pages, in ST format, added to the PDF file Any references to Waferscale, WSI, EasyFLASH and PSDsoft 2000 updated to ST, ST, Flash+PSD and PSDsoft Express
31-Jan-2002
1.1
2/3
PSD4135G2
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2002 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. www.st.com
3/3

▲Up To Search▲

Price & Availability of PSD4135F1V-B-12B81

	To Download PSD4135F1V-B-12B81 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .